Sharp MD-MT866H operation manual Power, About the liquid crystal display LCD About charging time

Page 13

	About the liquid crystal display (LCD)			About charging time
The condition of the portable MD will be shown on the LCD				After about 3.5 hours have passed, “						” will go out.	–
The condition of the portable MD will be shown on the LCD				After about 3.5 hours have passed, “						” will go out.
when inserting it into the battery charger.
when inserting it into the battery charger.				● Charge the battery within the range of 5°C - 35°C (41°F							Battery
		● Charging.		● Charge the battery within the range of 5°C - 35°C (41°F							Battery
				Notes:
	Display	Conditions		● This portable MD should only be used within the range
	Display	Conditions		of 0°C - 40°C (32°F - 104°F).
				of 0°C - 40°C (32°F - 104°F).
				- 95°F).
				- 95°F).

●The unit can be left in the charging state after it is com-

pleted.DEUTSCH

●If the MiniDisc unit is not to be used for some time,

remove the battery. (The battery drains gradually even

Source

Rechargeablethe

Power

Scrolling

when the power is turned off.)

FRANÇAIS

● Carry the battery in the supplied case.

● The charging is complete.

Caution:

ESPAÑOL

● When the portable MD is not in-

● Use the specified battery AD-N55BT only. Do not charge

serted correctly to the battery

a battery (nickel-cadmium, alkaline, etc.) other than

that

with

charger, or

Rechargeable terminal is dirty, it

specified.

SVENSKA

● Do not remove the outer cover of the re-

may not be possible to charge the

Turns off

chargeable battery. It may cause heat gen-

ITALIANOUsing

battery. (Wipe the terminal by cot-

eration, fire, or explosion.

ton swab.)

● Do not dip the battery in water, do not dis-

–

● Refreshing (see page 38).

pose of it in a fire, and do not take it apart.

NEDERLANDS

The unit checks and, if necessary,

● If the rechargeable battery terminal is dirty, charging

may

discharge the rechargeable bat-

not start. In such a case, wipe off the dirt with a dry cloth.

tery to recharge it automatically.

● Do not disassemble the battery.

ENGLISH

(At this time battery indicator is

flashing.)

13

Web-site:www.sharp.co.uk/support Help Line: 08705 274277 (office hours)

Image 13

Contents Thank you for purchasing this Sharp product MD-MT866HAccessories Contents Important Introduction Special NotesSpecial Notes Introduction Precautions PrecautionsAvoid using or leaving the unit in the following places Storing the unitMain unit Names of Controls and IndicatorsMain unit display panel Important Introduction Names of Controls and IndicatorsRemote control display panel Remote control unitIndicators NamesBattery- Charger Names Setting Battery ChargerFace the top Charge Toward you Mode Battery How to use the Charge / Operation switchRemoving For use with the AC adaptorPower Source Using with the Rechargeable Battery Using with the Rechargeable BatteryCharging About the liquid crystal display LCD About charging time PowerDisplay Conditions Using with Using with the AC AdaptorOperation mode SourceRelease Lock Open PressPreparation Hold FunctionHold Function Inserting a MiniDisc Inserting a MiniDiscConnections ConnectionsYou can record your favorite CDs or tapes to an MD To the DC in 5V socket To the Optical Line in socket50/60Hz 5V socket To the wall socket To the DCTo the Optical Line in socket Basic Operation Recording RecordingBefore Recording Digital recording Press the REC button+12 -12dB To interrupt recording To update the recorded contents of the MiniDiscTo stop recording About the TOCOperation Helpful tip when attaching a labelRecording BasicBasic PlaybackPlayback Before Playing backTo turn off the power Volume controlBass control To interrupt playbackTo locate the beginning of a track Advanced PlaybackRandom play or repeat play Useful Features Advanced PlaybackTo interrupt fast playback To return to normal playbackAdvanced Recording Press the Mode button whilst the record- ing is paused Useful Features Advanced RecordingLong-play recording monaural recording Start recordingYou can erase a portion of a track and make a new recording Press the right shuttle switch toward ENTER/SYNCTo create your own track numbers When a recording is paused or whilst recording…Recording tracks as a single track You can create your own track numbers at any pointAbout sampling rate converter About track numbersTo write recorded contents on the MiniDisc Useful Features Recording from a MicrophoneRecording from a Microphone To record from a microphoneRecording from a Microphone Track intervals UsefulDuring a mic manual recording During a mic synchro recordingChecking Displays Useful Features Checking DisplaysTo check the elapsed time and remaining time of the track During playback, press the Disp buttonVidual track To display the playing time of an indiTrack number and track name Press the Disp button to display the playFeatures Changing Default SettingsDefault Settings ChangingAuto power save Display backlight on the remote controlBeep sound Auto playAdvanced Titling a MiniDiscMiniDisc Titling aTo erase a character Characters symbolsTo enter a space To add charactersWhat is a MiniDisc for stamping? What is a master MiniDisc?Stamping titles from another MiniDisc Before stampingOperation of the MiniDisc for stamping Press the right shuttle switch toward ENTER/SYNC again Advanced FeaturesEditing a Recorded MiniDisc To erase tracks one at a timeTo combine tracks To divide a trackPress the Edit button repeatedly to select Divide Press the Edit button repeatedly to select CombineTo move a track AD-CA55X White RedReferences Other Features and Caution Resuming auto play Other Features and CautionRechargeable battery MiniDisc System Limitations Symptom LimitationsError Messages Error MessagesReferences Tr. Protect No SignalTroubleshooting TroubleshootingMaintenance MaintenanceIf trouble occurs Moisture condensationSpecifications SpecificationsWeight DimensionsSignal readout Error correctionSharp Corporation