Sharp MD-MT866H operation manual Error Messages, References

Page 50

References

– Error Messages –

50

Error Messages

ERROR MESSAGES

 

MEANING

 

REMEDY

BATT EMPTY

The battery is run down.

Charge the rechargeable battery or replace the alkaline bat-

(LoBATT)

 

 

tery (or use the AC adaptor for power).

 

BLANK MD

Nothing is recorded.

Replace the disc with a recorded disc.

(BLANK)

 

 

 

 

Can’t COPY

You tried to record from a copy prohib-

Record using the analogue cable.

(Can’tC)

ited MiniDisc.

 

 

Can’t EDIT

A track cannot be edited.

Change the stop position of the track and then edit it.

(Can’tE)

 

 

 

 

Can’t READ *

The disc data cannot be read because the

Reload the disc.

(Can’tS)

disc is damaged.

Replace it with another recorded disc.

(Can’tT)

 

 

 

 

(Can’tU)

 

 

 

 

Can’t REC

Recording cannot be performed correctly

Re-record or replace it with another recordable disc.

(Can’tR)

due to vibration or shock.

 

 

Can’t STAMP

Stamp function does not work.

Check the number of tracks.

 

Can’t WRITE

Cannot save the TOC information correctly

Replace the disc with another recordable disc.

(Can’tW)

to a MiniDisc. (A large portion of the disc

 

 

 

 

has been damaged.)

 

 

CHARGEmode

The Charge/Operation switch is not set to

Set the Charge/Operation switch to the operation mode.

 

 

the operation mode when using this unit

 

 

 

 

with the AC adaptor.

 

 

DEFECT

The disc is scratched.

If the sound you hear is not right, record again.

(DEFECT)

 

 

Replace the disc with another recordable disc.

 

DISC FULL

The disc is out of recording space.

Replace it with another recordable disc.

Er-MD **

The microprocessor has reported a sys-

To have it repaired, go to the distributor where you purchased

 

(ErMD*)

tem fault and the unit is out of order.

the unit.

 

HOLD

The unit is in the hold mode.

Return the HOLD switch to its original position.

(HOLD)

 

 

 

 

LOCKED

You removed a MiniDisc whilst recording

Turn off the power and remove the MiniDisc.

(Can’tLOCK)

or editing.

 

 

 

 

 

 

 

 

Web-site:www.sharp.co.uk/support Help Line: 08705 274277 (office hours)

Image 50
Contents MD-MT866H Thank you for purchasing this Sharp productAccessories Contents Special Notes Special NotesImportant Introduction Introduction Avoid using or leaving the unit in the following places PrecautionsPrecautions Storing the unitNames of Controls and Indicators Main unitImportant Introduction Names of Controls and Indicators Main unit display panelIndicators Remote control unitRemote control display panel NamesFace the top Charge Toward you Mode Battery ChargerBattery- Charger Names Setting Removing How to use the Charge / Operation switchBattery For use with the AC adaptorCharging Using with the Rechargeable BatteryPower Source Using with the Rechargeable Battery Display Conditions PowerAbout the liquid crystal display LCD About charging time Operation mode Using with the AC AdaptorUsing with SourceOpen Press Release LockHold Function Hold FunctionPreparation Inserting a MiniDisc Inserting a MiniDiscYou can record your favorite CDs or tapes to an MD ConnectionsConnections To the DC in 5V socket To the Optical Line in socketTo the Optical Line in socket To the DC50/60Hz 5V socket To the wall socket Before Recording RecordingBasic Operation Recording +12 -12dB Press the REC buttonDigital recording To stop recording To update the recorded contents of the MiniDiscTo interrupt recording About the TOCRecording Helpful tip when attaching a labelOperation BasicPlayback PlaybackBasic Before Playing backBass control Volume controlTo turn off the power To interrupt playbackAdvanced Playback To locate the beginning of a trackTo interrupt fast playback Useful Features Advanced PlaybackRandom play or repeat play To return to normal playbackAdvanced Recording Long-play recording monaural recording Useful Features Advanced RecordingPress the Mode button whilst the record- ing is paused Start recordingPress the right shuttle switch toward ENTER/SYNC You can erase a portion of a track and make a new recordingRecording tracks as a single track When a recording is paused or whilst recording…To create your own track numbers You can create your own track numbers at any pointAbout track numbers About sampling rate converterRecording from a Microphone Useful Features Recording from a MicrophoneTo write recorded contents on the MiniDisc To record from a microphoneRecording from a Microphone During a mic manual recording UsefulTrack intervals During a mic synchro recordingTo check the elapsed time and remaining time of the track Useful Features Checking DisplaysChecking Displays During playback, press the Disp buttonTrack number and track name To display the playing time of an indiVidual track Press the Disp button to display the playDefault Settings Changing Default SettingsFeatures ChangingBeep sound Display backlight on the remote controlAuto power save Auto playMiniDisc Titling a MiniDiscAdvanced Titling aTo enter a space Characters symbolsTo erase a character To add charactersStamping titles from another MiniDisc What is a master MiniDisc?What is a MiniDisc for stamping? Before stampingOperation of the MiniDisc for stamping Editing a Recorded MiniDisc Advanced FeaturesPress the right shuttle switch toward ENTER/SYNC again To erase tracks one at a timePress the Edit button repeatedly to select Divide To divide a trackTo combine tracks Press the Edit button repeatedly to select CombineTo move a track White Red AD-CA55XRechargeable battery Other Features and CautionReferences Other Features and Caution Resuming auto play Symptom Limitations MiniDisc System LimitationsReferences Error MessagesError Messages No Signal Tr. ProtectTroubleshooting TroubleshootingIf trouble occurs MaintenanceMaintenance Moisture condensationSpecifications SpecificationsSignal readout DimensionsWeight Error correctionSharp Corporation