Jabra GO 6470 user manual Replacing the Earbud, Pairing with Bluetooth wireless technology Devices

Page 39

Attaching the Head- or Neckband

To attach the head- or neckband:

1. Remove the current wearing-style attachment, if any.

2. Align the earbud and fitting of the headset with the matching holes on the head- or neckband and press until it clicks into place.

3. Put on the headset and rotate the microphone until it is as close as possible to your mouth.

Figure 43: Attaching the Jabra GO headset to a head- or neckband

Removing a Wearing-Style Attachment

To remove a wearing-style attachment, perform the opposite procedure to that described above for attaching it.

7.3Replacing the Earbud

After extensive use, the earbud of the Jabra GO headset may become worn, dirty and/or uncomfortable. Two extra, differently shaped earbuds are included with your headset. Otherwise, you can order replacement earbuds from GN at any time.

To remove the earbud, hold the headset with the earbud facing you and twist the earbud gently anti-clockwise until it comes free. Then align the replacement earbud onto the same fitting and gently press it down until it clicks into place (do not rotate).

7.4PAIRING with Bluetooth® wireless technology Devices

Pairing the Headset with a Mobile Phone

To use Bluetooth®, you must set up the wireless communication between the Jabra GO headset and your mobile phone by pairing them. The setup wizard helps you to do this during initial setup, but can also pair the headset manually at any time using the procedure below.

1.If your headset is currently turned on, turn it off by pressing and holding on its multifunction button for about 4 seconds — until its LED gives four quick flashes and then turns off.

2.Put your (powered-off) headset in pairing mode by pressing and holding on its multifunction button for about 4 seconds — until its LED lights a constant blue.

4 sec.

3.Make sure that Bluetooth® is active on your mobile phone and put your phone into Bluetooth® pairing mode. The exact procedure for doing this varies by mobile phone manufacturer and model — see your mobile phone manual for details.

Jabra GO 6470 User manual

39

Image 39

Contents Jabra GO Contents Daily Use Calling, Answering and Hanging Up 10.3 Jabra GO Touchscreen Base10.1 10.211.5 11.111.2 11.4Introduction Jabra GO Headset featuresJabra GO Base features Jabra GO Travel Charger featuresProtection level Criteria for selecting Important Safety InformationRead the Safety guide Protecting your Hearing with SafeTone Intellitone Noise-Exposure ProtectionOther Specifications Care and MaintenanceProduct Overview Package ContentsJabra GO 6400 series accessories Optional AccessoriesMultifunction button answer/end call, among other functions Jabra GO Headset DiagramJabra GO base, seen from the front and back, respectively Jabra GO Base DiagramSetup Overview and Background System Setup and ConnectionsQuick-Start Setup Wizard Apply Power to the Jabra GO BaseAssembling the Jabra GO Base and Headset Wearing the Jabra GO headset in various styles Assemble the HeadsetPlace the Headset in its Cradle Desk phone with headset port Connecting the Jabra GO Base to Your Desk PhoneIdentifying Your Desk Phone Features Standard desk phoneConnecting to a desk phone without a headset port Connecting to a Desk Phone without a Headset PortConnecting to a Proprietary Headset Port Connecting to a Standard Headset PortSetting the Clear Dial-tone Switch to find a Clear Dial-tone Configuring the Jabra GO Base for Your Desk PhoneIf the Jabra GO base cannot contact the Jabra test server Setting the Microphone LevelSet microphone level Using a Handset Lifter or Electronic HookswitchGN1000 Connecting to the GN1000 Remote Handset LifterGN1000 Connecting to a Phone with an Electronic Hookswitch Connecting to a Load-detect equipped PhoneConnecting to a Phone using RHL Mode Connecting the Jabra GO Base to Your Computer Configuring the base for your softphonePairing Your Headset with a Mobile Phone Installing and Running the Jabra PC Suite Check for Updates result window in Jabra Control Center Applying Firmware UpdatesCentral Administration and Mass Deployment Target Phone Concept Headset Controls and IndicatorsHeadset Visual and Audio Indicators Daily Use Calling, Answering and Hanging UpStandard Mobile Phone Dialing How to Make a CallCalling through a Softphone Voice-Activated Mobile Phone DialingCalling through a Desk Phone How to answer a callHanging up Do one of the following to answer the callFor all other types of phones Controlling the Speaker Volume and Microphone Switching between Your Phone and HeadsetDesk Phones Managing Call Collisions and Call Waiting Last Number RedialManaged from the headset Listening to MusicAttaching the Ear Hook for either Ear How to Wear the HeadsetJabra GO Headset Assembling or Changing the Wearing StyleAttaching the Head- or Neckband Pairing with Bluetooth wireless technology DevicesPairing the Headset with a Mobile Phone Replacing the EarbudManaging Your Bluetooth Connections Pairing the Headset with a Jabra GO BaseGesture name How to make it Headset Controls and SignalsAudio signal tones Headset visual indicatorFunction Tap Double Press Long Press State or event Tone description Headset Signal TonesChoosing Voice or Tones for Target indicators Headset Visual Indicators LEDHeadset state Recharging the Headset Battery Indicators and RechargePOwer save mode Battery indicatorsNarrowband vs. Wideband Audio High capacity Jabra Go InstallationsStaying within Range Microphone Noise BlackoutManaging Bluetooth Connections and the Pairing Table Clearing the Bluetooth Pairing TableMaking and changing Connections Mobile phone connection is lost Status bar Jabra GO Base Connections and SetupUsing the Touchscreen Jabra GO Touchscreen BaseFor MSH Users Only Standard OperationCall Options Call options menuPC & Softphone Phone menuManaging Call Collision Msh phone active call screenOne or more calls on hold call waiting Managing Call WaitingManaging call waiting one or more calls are on hold Settings SettingS MenuHeadset Docking-Operation Advanced settings menuReplacing the Cradle Jabra GO Base Audio IndicatorsSetup Wizard touch here to run the whole setup wizard Theft ProtectionShown Web conferencingAudio-hold and call switching Overview what is possible?Call Switching To display Audio On-HOLDUsing the Jabra GO Travel Charger Jabra GO Travel Charger DiagramStoring the Headset and USB Bluetooth Adapter Communicating with a PC Charging the Headset with the Travel ChargerJabra Link 350 USB Bluetooth Adapter Setup and Connection Jabra Link 350 USB Bluetooth AdapterJabra Link 350 USB Bluetooth Adapter Diagram Purpose of the USB Bluetooth AdapterPairing the Adapter and Headset Slow-flashing green lightConstant blue light Function Tap Press Jabra Link 350 USB Bluetooth Adapter Visual IndicatorsJabra Link 350 USB Bluetooth Adapter MFB Adapter Status LED SignalCan’t contact the dial-in server. What should I do? FAQs and TroubleshootingWhy doesn’t my computer detect the Jabra GO 6470 base? How do I pair my headset with the Jabra GO 6470 base?Hear myself when I talk using my desk phone. What can I do? What is the Talk Time of a Jabra GO 6400 HEADSET? What is the range on the Jabra GO 6470?USA and Canada Getting AssistanceEurope Middle East/AfricaTechnical Specifications HeadsetHeadset Hearing Protection Headset Battery Materials and AllergiesJabra GO Base Jabra Link 350 USB Bluetooth Adapter Certifications and Safety Approvals Jabra GO Travel ChargerProduct Disposal GlOSSARY USB Bluetooth adapter Softphone driverWideband audio RevD