NordicTrack NTL25530 user manual Troubleshooting, Problem The power turns off during use, Solution

Page 28

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-

free at 1-888-825-2588, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor that meets all of the specifications described on page 9. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c.Check the on/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the on/off circuit breaker has tripped. To reset the on/off circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key fully into the console.

d.Make sure that the on/off circuit breaker is in the reset position.

e.If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The displays of the console do not function properly

 

SOLUTION:

a. Remove the key from the console and

unplug the

 

power cord.

Remove the indicated Screws (48) from

 

the Hood (62). Carefully rotate and lift the Hood.

 

Locate the Reed Switch (37) and the Magnet (31) on

 

the left side of the Pulley (30). Turn the Pulley until the

 

Magnet is aligned with the Reed Switch.

Make sure

that the gap between the Magnet and the Reed

 

Switch is about 1/8”.

If necessary, loosen the Screw

(93)and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

a

48

 

62

 

48

1/8”

93

30

37

31

Top

 

View

 

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents QUESTIONS? Customer HOT LineTable of Contents Important Precautions Never insert or drop any object into any opening Using the 7200 R treadmill Before YOU BeginLeft Side Right SideAssembly Assembly requires two peopleWire cutters Adjustable Wrench With the help of a second person, carefully raise bothConnector and try again 83Be. careful not to pinch the wiresDo not tighten the Bolts yet Parts are properly tightened before you use the treadmillHOW to PUT on the Chest Pulse Sensor Chest Pulse Sensor Care and MaintenanceChest Pulse Sensor Troubleshooting Self near the center of the walking beltHOW to Plug in the Power Cord Performant LubeThis product must be grounded.If it should malfunc Grounded outlet is not available Grounded Outlet BoxFree Features of the ConsoleMore information 2Plug in the power cord Move the on/off circuit breaker to the reset poEnter your weight To reduce the possibility of electric shock2Select the manual mode Start the walking beltChange the incline of the treadmill as desired Training Zone displayDistance/Laps Stand on the foot RailsAvoid Moving your Turn on the fans if desiredHOW to USE Preset Programs 2Select the desired preset programInsert the key fully into the console Start the programWhen the program has ended, remove the key Next segmentFollow your progress with the displays Step onto the foot rails2Select one of the custom programs HOW to Create Custom ProgramsPress the Start button or the Speed + button HOW to USE Custom Programs HOW to USE Heart Rate Programs Rate setting Each heart rate program is divided into several timeThis occurs, see BeginningHOW to Connect Your Portable Stereo HOW to Connect Your Portable CD PlayerVideocassettes HOW to Connect Your Computer HOW to Connect Your Home StereoPhones jack, see instruction B RCA HOW to Connect Your VCRPrograms Next settings of the CD or video program When the CD or video program is completed,If you are using your portable CD player See onNext settings of the program HOW to USE Programs Directly from OUR WEB SiteFollow the on-line instructions to start Program Information MODE/DEMO Mode Buttons on the console will not operate If a D ap Pears in the displayHOW to Fold the Treadmill for Storage HOW to Move the TreadmillHOW to Lower the Treadmill for USE Hold the upper end of the treadmill with your right handHold the treadmill firmly with both hands, and lower Jury, bend your legs and keep your back straightTroubleshooting Problem The power turns off during useSolution Power cordProblem The walking belt slows when walked on Power CordProblem The treadmill rocks during use Shifted to the leftProblem The heart rate monitor does not function properly Battery from the sensor unit. Insert a newTurn it to the closed position Battery Cover Rubber Gasket Console, press one of the Incline buttonsConditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Page Qty Description Key No. Qty Description Key No. Qty Ordering Replacement Parts115 Left Cup Holder R0703A NTL25530 Limited Warranty Part No R0703A
Top Page Image Contents