Diamondback 1260Ef manual Assembly Instructions, Rear Stabilizer Bar

Page 7

1260OM 5/31/06 7:11 PM Page 9

Assembly Instructions

Step 1: Rear Stabilizer Bar

1.Place rear stabilizer bar under rear mainframe and align the screw holes.

2.Insert and tighten these two (M8 x 16mm) screws, split lock washer and flat washers using 6mm Allen wrench.

Step 2: Console Mast Assembly

1.Slide console mast cover onto console mast, making sure it is facing the right direction.

2.Connect the plug to the plug receptor of the main wire harness inside the console mast, taking care to install correctly. (See plug alignment marks)

3.Install the console mast by carefully sliding it onto the console mast receptor while pulling the wire harness. This will keep the slack out of the harness so that the wires will not be pinched and short out.

HINT: Pay attention to the wire harness while sliding the console mast and do not pinch the wire harness. Failing to do so will result in a void warranty.

4.Insert the four screws (M8 x 16mm), spring washer and washers into console mast and hand tighten them. Note: do not tighten them until you have all 4 sets of screws, split lock washers and flat washers inserted. Finally, tighten all of them with attached 6mm Allen wrench.

5.Place console mast cover in place and align it with snap holes. Snap the console mast cover into main side cases, making sure all snaps are in place.

6.Insert and tighten console mast cover with two screws (M5 x 12mm) using a Phillips screwdriver.

7.Peel the rubber mats and place them on the accessory trays.

Step 3: Handlebar Assembly

1.Insert the hand pulse harness through the opening of the console mast and out the top of the console mounting plate.

2.Assemble the handlebar onto the mount and insert and tighten four screws (M6 x 12mm), split lock washers and flat washers using 4mm Allen wrench. Be sure not to pinch the hand pulse wire harness during this procedure, as this will damage the electronic console.

Step 4: Console Assembly

1.Un-tighten the main wire harness on the console mast. Connect both plugs to the plug receptors on the backside of the console, taking care to install correctly (see plug alignment marks).

WIRING HARNESS INSTALLATION HINT: Any excess wiring must be carefully inserted (stored) back into console mast before installing the console onto the console mounting plate.

2.Fasten the console to the console mounting plate with four (M5 x 12mm) screws using a Phillips screwdriver.

Step 5: Handrail Assembly

1.Insert Right handrail (See “R” mark on the mounting plate) into handrail receptor and align the screw holes of two mounting plates.

2.Insert and tighten four (M6 x 12mm) screws, split lock washers and flat washers with attached 4mm Allen wrench.

3.Install the handrail cover by tighten two (M5 x 8mm) screws using a Phillips screwdriver. Make sure the oblong opening is facing up and on the handrail side.

4.Repeat this assembling process for the Left handrail and its cover.

Step 6: Power Cord

1.Place the elliptical equipment on a solid, leveled floor.

2.Plug the power cord into a wall outlet and turn the power switch ON.

1260Ef Owner’s Manual

5

 

 

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 1260OM 5/31/06 711 PM Product Name Diamondback 1260Ef Elliptical Serial Number Purchaser’s Reference InformationTable of Contents Introduction Save this Operating Instructions Manual for Your Refernce Safety Instructions and WarningsAssembly Drawing Rear Stabilizer Bar Assembly InstructionsHeart rate is an important key to your exercise Workout guidelinesGood health is an exercise in common sense ’10Heart Rate Guidelines 60% 85% Maximum Target Maximum Heart Rate & Training ZoneQuantity & Quality Get a smart start on exercisingOperating Tips Pulse Hand Grips StandardChest Strap Standard Console Default valuesGlossary of Terms Console Console Layout Heart rate bar graph display Dot Matrix/Profile Display Heart Rate Bar GraphMessage/Workout Data display Dot Matrix /Profile displayStart key Level Up/Down keysIncline Up/Down keys Enter keyStop/Reset key Warm UP Workout ProgramsCool Down Workout Summary Quick Start Program Default ValuesQuick Start Key Classic Programs Display Accepting default values or Entering the program setup modeClassic Programs N U a LWorkout Programs N D O M C R O S S T E R V a L L L C L I M B R I N T Workout Programs R G E T H R HR Interactive ProgramsHR Interactive Programs Workout Programs I N T E R V a L Workout Programs T B U R N E R H I L L Workout Programs R D I O U T E B U R N E R Cross Training ProgramsCross Training Programs Workout Programs A D B U I L D E R T a L T R a I N E R Personal Trainer Key Personal TrainerHR Lock Key HR LockWorkout Programs Select User Program and Beginning the Program User 1 & UserUser 1 & User Key Save a program into User 1 or UserWorkout Programs Maintenance Domestic warranty Information Additional Rights Warranty voided ifParts & Service ExclusionsDiamondback Fitness Warranty Card Warranty cardDiamondback Fitness
Top Page Image Contents