Healthrider manual Questions?, Model No. WESY8630C3 Serial No, Serial Number Decal Under Seat

Page 1

Model No. WESY8630C3

Serial No.

Write the serial number in the space above for future reference.

Serial Number Decal (Under Seat)

QUESTIONS?

As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or find there are missing or damaged parts, we will guarantee you complete sat- isfaction through direct assis- tance from our factory.

TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER

HOT LINE. The trained techni- cians on our customer hot line will provide immediate assis- tance, free of charge to you.

CUSTOMER HOT LINE:

1-888-936-4266

Mon.–Fri., 8 a.m.–6:30 p.m. EST (excluding holidays)

CAUTION

Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference.

USER'S MANUAL

Patent Pending

Visit our website at

www.weiderfitness.com

new products, prizes, fitness tips, and much more!

Image 1

Contents Model No. WESY8630C3 Serial No QUESTIONS?Serial Number Decal Under Seat Customer HOT LineLimited Warranty Table of ContentsRead all instructions in this manual Important PrecautionsSure that the cables are on all of the pulleys Decal shownBefore YOU Begin Using the WeiderAssembly Frame Assembly BAG TWO Be sure that the pins on Stack of WeightsDo not over Tighten the Nylon Locknut Be sure that the pinLocknuts used in steps 1 through Do not tighten Nylon Locknuts yetAs shown Nylon LocknutShown Only once Right Arm 5. Be sure that the upperOrder new Retainers Be sure thatOnto the Bolt, but do not fully tighten it Identify the Butterfly Cable 89-this isPulley Plates 31 and 3 1/2 Pulleys PulleyGroove of the Pulley ButBolt, but do not fully tighten it. Leave Shortest CableSure that the Cable Trap is inside Pre-assembledBase 13 with a 3/8 x 2 Bolt 50 and a 3/8 Cable Trap is turned to hold the Cable in placePlace Direction shownUpper Pulley move smoothly Be sure that Large Cable Trap is turned to holdPivot Identify the High Cable 85-this is 3/8 x 5 Bolt 74 and the 3/8 Nylon LocknutHigh Cable around a 3 1/2 Pulley 82. Attach Bolt 76, a 3/8 Washer 38, and a 3/8 Nylon LocknutIndicated side Nylon Locknut 42. Do not overtightenBe sure that the Cable Trap is in the indi- cated position Seat Plate to the Seat 17 with two 1/4 x 3/4 Screws Press a 1 1/2 Square Inner Cap 57 into the Rear Seat FramePress a 1 1/2 Square Inner Cap 57 into the Leg Lever With the Bolt and a 5/16 Nylon LocknutPress two 3/4 Round Inner Caps 78 into each Pad Tube TROUBLE-SHOOTING and Maintenance onChanging the Weight Setting HOW to USE the Training SystemAttaching the LAT BAR or Nylon Strap to High Pulley Station Attaching the LAT BAR or Nylon Strap to LOW Pulley StationStation Adjusting the LEG Press PlateAttaching and Removing the Seat Attaching the LEG Lever to the LOW Pulley StationLbs Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceSee drawing 1. Remove the 3/8 Nylon Locknut 42 Rear Cable 87 can be tightened in the same mannerLong U Bracket Cable DiagramsLow Pulley Butterfly CableTop Frame High CablePart No R0600A Ordering Replacement PartsRefers to the key number of the part Check to see if it has been pre-assembledX 3 1/4 Bolt 16 x 1 3/4 Bolt2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference Qty Description R0600A16 x 1 Bolt X 8 BoltExploded DRAWING-Model No. WESY8630C3