Healthrider WESY8630C3 manual Do not tighten Nylon Locknuts yet, Locknuts used in steps 1 through

Page 8

FRAME ASSEMBLY

8. Lubricate the insides of the holes in the Top		8
Weights (24) as shown. Slide a Top Weight		8
Weights (24) as shown. Slide a Top Weight
onto each set of Weight Guides (23).
					24
		24			Lubricate
		24
					23
		Lubricate
		23
9. Attach the Top Frame (2) to the Ab Upright (1)		9
with two 5/16” x 2 3/4” Bolts (55), two 5/16”		9			55
with two 5/16” x 2 3/4” Bolts (55), two 5/16”					55
Washers (20), and two 5/16” Nylon Locknuts			20
(40). Do not tighten the Nylon Locknuts			20
yet.			55
yet.
Attach the Butterfly Frame (3) to the Leg		20			3
Press Upright (4) with two 5/16” x 2 3/4” Bolts		2
(55), two 5/16” Washers (20), and two 5/16”
Nylon Locknuts (40).	Do not tighten the
Nylon Locknuts yet.
		1	40	40	4
10. Attach the upper ends of one set of Weight		10
Guides (23) to the Top Frame (2) with a 5/16”		10			69
Guides (23) to the Top Frame (2) with a 5/16”			40		69
x 6” Bolt (67), two 1/2” x 3/4” Spacers (69),			40
and a 5/16” Nylon Locknut (40).			69		23
		40	69		23
Attach the upper ends of the other set of		40			67
Attach the upper ends of the other set of					67
Weight Guides (23) in the same manner.		2
		2
Before continuing, firmly tighten all nylon
locknuts used in steps 1 through 10.			67
			23
		8

Image 8

Contents QUESTIONS? Model No. WESY8630C3 Serial NoSerial Number Decal Under Seat Customer HOT LineTable of Contents Limited WarrantyImportant Precautions Read all instructions in this manualSure that the cables are on all of the pulleys Decal shownUsing the Weider Before YOU BeginAssembly Frame Assembly BAG TWO Stack of Weights Be sure that the pins onDo not over Tighten the Nylon Locknut Be sure that the pinDo not tighten Nylon Locknuts yet Locknuts used in steps 1 throughShown Nylon LocknutAs shown Right Arm 5. Be sure that the upper Only onceOrder new Retainers Be sure thatIdentify the Butterfly Cable 89-this is Onto the Bolt, but do not fully tighten itPulley Pulley Plates 31 and 3 1/2 PulleysGroove of the Pulley ButShortest Cable Bolt, but do not fully tighten it. LeaveSure that the Cable Trap is inside Pre-assembledCable Trap is turned to hold the Cable in place Base 13 with a 3/8 x 2 Bolt 50 and a 3/8Upper Direction shownPlace Be sure that Large Cable Trap is turned to hold Pulley move smoothly3/8 x 5 Bolt 74 and the 3/8 Nylon Locknut Pivot Identify the High Cable 85-this isHigh Cable around a 3 1/2 Pulley 82. Attach Bolt 76, a 3/8 Washer 38, and a 3/8 Nylon LocknutNylon Locknut 42. Do not overtighten Indicated sideBe sure that the Cable Trap is in the indi- cated position Press a 1 1/2 Square Inner Cap 57 into the Rear Seat Frame Seat Plate to the Seat 17 with two 1/4 x 3/4 ScrewsPress a 1 1/2 Square Inner Cap 57 into the Leg Lever With the Bolt and a 5/16 Nylon LocknutTROUBLE-SHOOTING and Maintenance on Press two 3/4 Round Inner Caps 78 into each Pad TubeHOW to USE the Training System Changing the Weight SettingAttaching the LAT BAR or Nylon Strap to High Pulley Station Attaching the LAT BAR or Nylon Strap to LOW Pulley StationAdjusting the LEG Press Plate StationAttaching and Removing the Seat Attaching the LEG Lever to the LOW Pulley StationWeight Resistance Chart LbsTROUBLE-SHOOTING and Maintenance Tightening the CablesSee drawing 1. Remove the 3/8 Nylon Locknut 42 Rear Cable 87 can be tightened in the same mannerCable Diagrams Long U BracketLow Pulley Butterfly CableHigh Cable Top FrameOrdering Replacement Parts Part No R0600ACheck to see if it has been pre-assembled Refers to the key number of the part16 x 1 3/4 Bolt X 3 1/4 Bolt2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference R0600A Qty Description16 x 1 Bolt X 8 BoltExploded DRAWING-Model No. WESY8630C3