Healthrider WESY8630C3 manual TROUBLE-SHOOTING and Maintenance, Tightening the Cables

Page 25

TROUBLE-SHOOTING AND MAINTENANCE

Inspect and tighten all parts each time you use the training system. Replace any worn parts immediately. The training system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.

TIGHTENING THE CABLES

Woven cable, the type of cable used on the training system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. If any slack is felt when using the weight stack closest to the ab upright, both the High Cable (85) and the Low Cable (86) will need to be tight- ened. If any slack is felt when using the other weight stack, the Rear Cable (87), the Press Cable (88), and the Butterfly Cable (89) will need to be tightened.

To tighten the cables, first insert the weight pin into the mid- dle of the weight stack. Slack can be removed from these cables several ways:

•See drawing 1. Tighten the 1/4” Nylon Locknut (44) that connects the end of the Press Cable (88) to the Large “U” Bracket (84).

•See drawing 1. Remove the 3/8” Nylon Locknut (42) and

the 3/8” x 2” Bolt (50) from the Cable Trap (80), Pulley, and Large “U” Bracket (84). Reattach the Pulley and

Cable Trap to the other hole in the Large “U” Bracket. Be sure that the Cable Trap is in the proper position and that the Cable and Pulley move smoothly.

•See drawing 2. Tighten the 1/4” Nylon Locknut (44) that connects the end of the High Cable (85) to the Small “U” Bracket (32).

The Rear Cable (87) can be tightened in the same manner.

•See Drawing 3. If you feel additional slack while using the training system, the Low Cable (86) and the Press Cable

(88)can be tightened further.

Remove the 3/8” x 2” Bolts (50), the 3/8” Nylon Locknuts

 

(42), the 3 1/3” Pulleys (82), and the Cable Traps (80)

 

from the Pulley Plates (31). Reattach the upper Pulley

 

without the Cable Trap

. Reattach the lower Pulley to the

 

higher hole in the Pulley Plates

without the Cable Trap

.

Keep the Cable Traps for future use. Be sure that the

Cable and Pulley move smoothly.

Do not overtighten the cables. If the cables are overtight- ened, the top weight will be lifted off the weight stack.

If a cable tends to slip off the pulleys often, it may have become twisted. Remove the cable and re-install it.

1

82

80

42

8450

44

88

2

87

85

32

 

 

44

32

 

44

3 82

42

5031

82

80

86, 88

If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Model No. WESY8630C3 Serial No QUESTIONS?Serial Number Decal Under Seat Customer HOT LineLimited Warranty Table of ContentsRead all instructions in this manual Important PrecautionsSure that the cables are on all of the pulleys Decal shownBefore YOU Begin Using the WeiderAssembly Frame Assembly BAG TWO Be sure that the pins on Stack of WeightsDo not over Tighten the Nylon Locknut Be sure that the pinLocknuts used in steps 1 through Do not tighten Nylon Locknuts yetAs shown Nylon LocknutShown Only once Right Arm 5. Be sure that the upperOrder new Retainers Be sure thatOnto the Bolt, but do not fully tighten it Identify the Butterfly Cable 89-this isPulley Plates 31 and 3 1/2 Pulleys PulleyGroove of the Pulley ButBolt, but do not fully tighten it. Leave Shortest CableSure that the Cable Trap is inside Pre-assembledBase 13 with a 3/8 x 2 Bolt 50 and a 3/8 Cable Trap is turned to hold the Cable in placePlace Direction shownUpper Pulley move smoothly Be sure that Large Cable Trap is turned to holdPivot Identify the High Cable 85-this is 3/8 x 5 Bolt 74 and the 3/8 Nylon LocknutHigh Cable around a 3 1/2 Pulley 82. Attach Bolt 76, a 3/8 Washer 38, and a 3/8 Nylon LocknutIndicated side Nylon Locknut 42. Do not overtightenBe sure that the Cable Trap is in the indi- cated position Seat Plate to the Seat 17 with two 1/4 x 3/4 Screws Press a 1 1/2 Square Inner Cap 57 into the Rear Seat FramePress a 1 1/2 Square Inner Cap 57 into the Leg Lever With the Bolt and a 5/16 Nylon LocknutPress two 3/4 Round Inner Caps 78 into each Pad Tube TROUBLE-SHOOTING and Maintenance onChanging the Weight Setting HOW to USE the Training SystemAttaching the LAT BAR or Nylon Strap to High Pulley Station Attaching the LAT BAR or Nylon Strap to LOW Pulley StationStation Adjusting the LEG Press PlateAttaching and Removing the Seat Attaching the LEG Lever to the LOW Pulley StationLbs Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceSee drawing 1. Remove the 3/8 Nylon Locknut 42 Rear Cable 87 can be tightened in the same mannerLong U Bracket Cable DiagramsLow Pulley Butterfly CableTop Frame High CablePart No R0600A Ordering Replacement PartsRefers to the key number of the part Check to see if it has been pre-assembledX 3 1/4 Bolt 16 x 1 3/4 Bolt2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference Qty Description R0600A16 x 1 Bolt X 8 BoltExploded DRAWING-Model No. WESY8630C3
Top Page Image Contents