Healthrider WESY8630C3 manual Press two 3/4 Round Inner Caps 78 into each Pad Tube

Page 21

55.Press two 3/4” Round Inner Caps (78) into each Pad Tube (28).

Insert a Pad Tube (28) into the Rear Seat Frame (16). Slide a Foam Pad (29) onto each end of the Pad Tube.

Insert the other Pad Tube (28) into the Leg Lever (15). Slide a Foam Pad (29) onto each end of the Pad Tube.

56. Attach the Large Backrest (19) to the Leg Press Upright (4) with two 1/4” x 2 1/2” Machine Screws (64) and two 1/4” Washers (37).

SEAT ASSEMBLY

57.Insert a 1/4” x 2 1/2” Carriage Bolt (60) through the center hole in a Seat Plate (41). Attach the Seat Plate to the Seat (17) with two 1/4” x 3/4” Screws (59).

Insert the 1/4” x 2 1/2” Carriage Bolt (60) through the indicated hole in the Front Seat Frame (8). Tighten a 1/4” Nylon Locknut (44) with a 1/4” Washer (37) onto the Carriage Bolt.

Attach the other end of the Seat (17) to the Front Seat Frame (8) with a 1/4” Washer (37) and a 1/4” x 2 1/2” Machine Screw (64).

55
	78	16
	78
	29
		28
	15		29
	15		78
			78
56		4
		4
	64		19
	64	37
		37
57
			17
		8	60
		41	60
		41
			59
		37
		64
			44

58. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained

in HOW TO USE THE TRAINING SYSTEM, beginning on page 22 of this manual.
Before using the training system, pull each cable a few times to be sure that the cables move smoothly
over the pulleys. If one of the cables does not move smoothly, find and correct the problem.	IMPOR-
TANT: If the cables are not properly installed, they may be damaged when heavy weight is
used. See the CABLE DIAGRAMS on page 26 and 27 of this manual for proper cable routing. If
there is any slack in the cables, you will need to remove the slack by tightening the cables. See
TROUBLE-SHOOTING AND MAINTENANCE on page 25.

21

Image 21

Contents Model No. WESY8630C3 Serial No QUESTIONS?Serial Number Decal Under Seat Customer HOT LineLimited Warranty Table of ContentsRead all instructions in this manual Important PrecautionsSure that the cables are on all of the pulleys Decal shownBefore YOU Begin Using the WeiderAssembly Frame Assembly BAG TWO Be sure that the pins on Stack of WeightsDo not over Tighten the Nylon Locknut Be sure that the pinLocknuts used in steps 1 through Do not tighten Nylon Locknuts yetNylon Locknut As shownShown Only once Right Arm 5. Be sure that the upperOrder new Retainers Be sure thatOnto the Bolt, but do not fully tighten it Identify the Butterfly Cable 89-this isPulley Plates 31 and 3 1/2 Pulleys PulleyGroove of the Pulley ButBolt, but do not fully tighten it. Leave Shortest CableSure that the Cable Trap is inside Pre-assembledBase 13 with a 3/8 x 2 Bolt 50 and a 3/8 Cable Trap is turned to hold the Cable in placeDirection shown PlaceUpper Pulley move smoothly Be sure that Large Cable Trap is turned to holdPivot Identify the High Cable 85-this is 3/8 x 5 Bolt 74 and the 3/8 Nylon LocknutHigh Cable around a 3 1/2 Pulley 82. Attach Bolt 76, a 3/8 Washer 38, and a 3/8 Nylon LocknutIndicated side Nylon Locknut 42. Do not overtightenBe sure that the Cable Trap is in the indi- cated position Seat Plate to the Seat 17 with two 1/4 x 3/4 Screws Press a 1 1/2 Square Inner Cap 57 into the Rear Seat FramePress a 1 1/2 Square Inner Cap 57 into the Leg Lever With the Bolt and a 5/16 Nylon LocknutPress two 3/4 Round Inner Caps 78 into each Pad Tube TROUBLE-SHOOTING and Maintenance onChanging the Weight Setting HOW to USE the Training SystemAttaching the LAT BAR or Nylon Strap to High Pulley Station Attaching the LAT BAR or Nylon Strap to LOW Pulley StationStation Adjusting the LEG Press PlateAttaching and Removing the Seat Attaching the LEG Lever to the LOW Pulley StationLbs Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceSee drawing 1. Remove the 3/8 Nylon Locknut 42 Rear Cable 87 can be tightened in the same mannerLong U Bracket Cable DiagramsLow Pulley Butterfly CableTop Frame High CablePart No R0600A Ordering Replacement PartsRefers to the key number of the part Check to see if it has been pre-assembledX 3 1/4 Bolt 16 x 1 3/4 Bolt2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference Qty Description R0600A16 x 1 Bolt X 8 BoltExploded DRAWING-Model No. WESY8630C3