Healthrider WESY8630C3 manual Identify the Butterfly Cable 89-this is

Page 11

18.Press a 1 3/4” Square Inner Cap (48) into the lower end of the Left Fly Arm (6). Wet the lower end of the Left Fly Arm with soapy water. Slide a 10” Pad (22) onto the Left Arm.

Repeat this step with the Right Fly Arm (5).

ARM ASSEMBLY

19.Locate and open the parts bags labeled “CABLE ASSEMBLY” and “PULLEYS.”

During steps 19 through 50, refer to the CABLE DIAGRAMS on pages 26 and 27 of this manual to verify proper cable routing. Before beginning this section, fully unwind the five Cables and identify the Cables by com- paring the lengths and the ends. The approxi- mate length of each Cable, in inches, is listed after the key number in the drawing.

IMPORTANT: While assembling the cables, do not overtighten the bolts and nuts attaching the pulleys. The pulleys must be able to turn freely.

CABLE ASSEMBLY

20.Insert a 5/16” x 1” Bolt (51) through the brack- et on the Right Fly Arm (5). Tighten a 5/16” Nylon Jam Nut (91) onto the Bolt.

Identify the Butterfly Cable (89)—this is the

second shortest Cable. Slide one end of the Butterfly Cable onto the 5/16” x 1” Bolt (51). Thread another 5/16” Nylon Jam Nut (91)

onto the Bolt, but do not fully tighten it.

Leave enough room between the two Jam Nuts for the Cable to pivot.

11

18
	6
5
	48
22	22
19
	87—72”
	89—82”
	85—101”
	86—110”
	88—239”
20
	91
	89
	5
	51

Image 11

Contents Customer HOT Line QUESTIONS?Model No. WESY8630C3 Serial No Serial Number Decal Under SeatLimited Warranty Table of ContentsDecal shown Important PrecautionsRead all instructions in this manual Sure that the cables are on all of the pulleysBefore YOU Begin Using the WeiderAssembly Frame Assembly BAG TWO Be sure that the pin Stack of WeightsBe sure that the pins on Do not over Tighten the Nylon LocknutLocknuts used in steps 1 through Do not tighten Nylon Locknuts yetShown Nylon LocknutAs shown Be sure that Right Arm 5. Be sure that the upperOnly once Order new RetainersOnto the Bolt, but do not fully tighten it Identify the Butterfly Cable 89-this isBut PulleyPulley Plates 31 and 3 1/2 Pulleys Groove of the PulleyPre-assembled Shortest CableBolt, but do not fully tighten it. Leave Sure that the Cable Trap is insideBase 13 with a 3/8 x 2 Bolt 50 and a 3/8 Cable Trap is turned to hold the Cable in placeUpper Direction shownPlace Pulley move smoothly Be sure that Large Cable Trap is turned to holdBolt 76, a 3/8 Washer 38, and a 3/8 Nylon Locknut 3/8 x 5 Bolt 74 and the 3/8 Nylon LocknutPivot Identify the High Cable 85-this is High Cable around a 3 1/2 Pulley 82. AttachIndicated side Nylon Locknut 42. Do not overtightenBe sure that the Cable Trap is in the indi- cated position With the Bolt and a 5/16 Nylon Locknut Press a 1 1/2 Square Inner Cap 57 into the Rear Seat FrameSeat Plate to the Seat 17 with two 1/4 x 3/4 Screws Press a 1 1/2 Square Inner Cap 57 into the Leg LeverPress two 3/4 Round Inner Caps 78 into each Pad Tube TROUBLE-SHOOTING and Maintenance onAttaching the LAT BAR or Nylon Strap to LOW Pulley Station HOW to USE the Training SystemChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to High Pulley StationAttaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateStation Attaching and Removing the SeatLbs Weight Resistance ChartRear Cable 87 can be tightened in the same manner TROUBLE-SHOOTING and MaintenanceTightening the Cables See drawing 1. Remove the 3/8 Nylon Locknut 42Butterfly Cable Cable DiagramsLong U Bracket Low PulleyTop Frame High CablePart No R0600A Ordering Replacement PartsRefers to the key number of the part Check to see if it has been pre-assembledX 3 1/4 Bolt 16 x 1 3/4 Bolt2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference X 8 Bolt R0600AQty Description 16 x 1 BoltExploded DRAWING-Model No. WESY8630C3