Healthrider WESY8630C3 manual Cable Trap is turned to hold the Cable in place

Page 14

29.Identify the Press Cable (88)—this is the longest Cable. Attach the end of the Press Cable (88) to the Large “U” Bracket (84) with a 1/4” Nylon Locknut (44) and a 1/4” Washer (37). Do not completely tighten the Nylon

Locknut. It should be threaded onto the end of the Cable so only a couple of threads are showing above the Nylon Locknut, as shown in the inset drawing.

30.Wrap the Press Cable (88) around a 3 1/2” Pulley (82). Attach the Pulley and a Cable Trap (80) to the indicated bracket on the

Press Base (13) with a 3/8” x 2” Bolt (50) and

a 3/8” Nylon Locknut (42). Be sure that the

Cable Trap is turned to hold the Cable in place.

CABLE ASSEMBLY

31.Wrap the Press Cable (88) around a 3 1/2” Pulley (82). Attach the Pulley and a Cable Trap (80) to the other bracket on the Press

Base (13) with a 3/8” x 2” Bolt (50) and a 3/8”

Nylon Locknut (42). Be sure that the Cable

Trap is turned to hold the Cable in place.

14

29
		44
		37	84
	44		84
	44
	37	88
	37
88	84
88
30
		88
		80	42
			42
		82
	50	13
31
		88
		80
			42
		82
	50	13
		13

Image 14

Contents Serial Number Decal Under Seat QUESTIONS?Model No. WESY8630C3 Serial No Customer HOT LineTable of Contents Limited WarrantySure that the cables are on all of the pulleys Important PrecautionsRead all instructions in this manual Decal shownUsing the Weider Before YOU BeginAssembly Frame Assembly BAG TWO Do not over Tighten the Nylon Locknut Stack of WeightsBe sure that the pins on Be sure that the pinDo not tighten Nylon Locknuts yet Locknuts used in steps 1 throughShown Nylon LocknutAs shown Order new Retainers Right Arm 5. Be sure that the upperOnly once Be sure thatIdentify the Butterfly Cable 89-this is Onto the Bolt, but do not fully tighten itGroove of the Pulley PulleyPulley Plates 31 and 3 1/2 Pulleys ButSure that the Cable Trap is inside Shortest CableBolt, but do not fully tighten it. Leave Pre-assembledCable Trap is turned to hold the Cable in place Base 13 with a 3/8 x 2 Bolt 50 and a 3/8Upper Direction shownPlace Be sure that Large Cable Trap is turned to hold Pulley move smoothlyHigh Cable around a 3 1/2 Pulley 82. Attach 3/8 x 5 Bolt 74 and the 3/8 Nylon LocknutPivot Identify the High Cable 85-this is Bolt 76, a 3/8 Washer 38, and a 3/8 Nylon LocknutNylon Locknut 42. Do not overtighten Indicated sideBe sure that the Cable Trap is in the indi- cated position Press a 1 1/2 Square Inner Cap 57 into the Leg Lever Press a 1 1/2 Square Inner Cap 57 into the Rear Seat FrameSeat Plate to the Seat 17 with two 1/4 x 3/4 Screws With the Bolt and a 5/16 Nylon LocknutTROUBLE-SHOOTING and Maintenance on Press two 3/4 Round Inner Caps 78 into each Pad TubeAttaching the LAT BAR or Nylon Strap to High Pulley Station HOW to USE the Training SystemChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to LOW Pulley StationAttaching and Removing the Seat Adjusting the LEG Press PlateStation Attaching the LEG Lever to the LOW Pulley StationWeight Resistance Chart LbsSee drawing 1. Remove the 3/8 Nylon Locknut 42 TROUBLE-SHOOTING and MaintenanceTightening the Cables Rear Cable 87 can be tightened in the same mannerLow Pulley Cable DiagramsLong U Bracket Butterfly CableHigh Cable Top FrameOrdering Replacement Parts Part No R0600ACheck to see if it has been pre-assembled Refers to the key number of the part16 x 1 3/4 Bolt X 3 1/4 Bolt2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference 16 x 1 Bolt R0600AQty Description X 8 BoltExploded DRAWING-Model No. WESY8630C3