Healthrider WESY8630C3 Station, Attaching and Removing the Seat, Adjusting the LEG Press Plate

Page 23

ATTACHING THE AB STRAP TO THE AB PULLEY

STATION

Attach the Ab Strap (35) to the Low Cable (86) at the ab pulley station with a Cable Clip (33).

ATTACHING AND REMOVING THE SEAT

To attach the Seat (17), set the bracket on the Rear Seat Frame (16) onto the pins on the Ab Upright (1). Attach the Rear Seat Frame to the Ab Upright with the 5/16” x 2 3/4” Carriage Bolt (77) and the Seat Knob (30).

For some exercises, the Seat (17) must be removed. First, be sure that the chain is not attached to the leg lever. Next, remove the Seat Knob (30) and the 5/16” x 2 3/4” Carriage Bolt (77) from the Rear Seat Frame (16). Lift the Rear Seat Frame off the Ab Upright (1).

ATTACHING THE LEG LEVER TO THE LOW

PULLEY STATION

To use the Leg Lever (15), the seat must be attached to the front upright (see ATTACHING AND REMOVING THE SEAT above).

Attach one end of the Chain (34) to the Low Cable

(86)with a Cable Clip (33). Attach the other end of the Chain to the Eyebolt (79) with a Cable Clip.

ADJUSTING THE LEG PRESS PLATE

Remove the Lock Pin (73) from the Adjustment Tube (10).

Align the holes in the Leg Press Arm (9) with the desired set of holes in the Adjustment Tube (10). Re- insert the Lock Pin (73) through the holes in the Leg Press Arm and the holes in the Adjustment Tube.

sure that the hook on the Lock Pin is clipped in place on the Adjustment Tube.

		86
		33
		35
		30
		17
		77
		16
		1
		33
	15
	79	34
	79	86
		86
		Hook
	73	10
	Be	9
	23

Image 23

Contents Customer HOT Line QUESTIONS?Model No. WESY8630C3 Serial No Serial Number Decal Under SeatLimited Warranty Table of ContentsDecal shown Important PrecautionsRead all instructions in this manual Sure that the cables are on all of the pulleysBefore YOU Begin Using the WeiderAssembly Frame Assembly BAG TWO Be sure that the pin Stack of WeightsBe sure that the pins on Do not over Tighten the Nylon LocknutLocknuts used in steps 1 through Do not tighten Nylon Locknuts yetShown Nylon LocknutAs shown Be sure that Right Arm 5. Be sure that the upperOnly once Order new RetainersOnto the Bolt, but do not fully tighten it Identify the Butterfly Cable 89-this isBut PulleyPulley Plates 31 and 3 1/2 Pulleys Groove of the PulleyPre-assembled Shortest CableBolt, but do not fully tighten it. Leave Sure that the Cable Trap is insideBase 13 with a 3/8 x 2 Bolt 50 and a 3/8 Cable Trap is turned to hold the Cable in placeUpper Direction shownPlace Pulley move smoothly Be sure that Large Cable Trap is turned to holdBolt 76, a 3/8 Washer 38, and a 3/8 Nylon Locknut 3/8 x 5 Bolt 74 and the 3/8 Nylon LocknutPivot Identify the High Cable 85-this is High Cable around a 3 1/2 Pulley 82. AttachIndicated side Nylon Locknut 42. Do not overtightenBe sure that the Cable Trap is in the indi- cated position With the Bolt and a 5/16 Nylon Locknut Press a 1 1/2 Square Inner Cap 57 into the Rear Seat FrameSeat Plate to the Seat 17 with two 1/4 x 3/4 Screws Press a 1 1/2 Square Inner Cap 57 into the Leg LeverPress two 3/4 Round Inner Caps 78 into each Pad Tube TROUBLE-SHOOTING and Maintenance onAttaching the LAT BAR or Nylon Strap to LOW Pulley Station HOW to USE the Training SystemChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to High Pulley StationAttaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateStation Attaching and Removing the SeatLbs Weight Resistance ChartRear Cable 87 can be tightened in the same manner TROUBLE-SHOOTING and MaintenanceTightening the Cables See drawing 1. Remove the 3/8 Nylon Locknut 42Butterfly Cable Cable DiagramsLong U Bracket Low PulleyTop Frame High CablePart No R0600A Ordering Replacement PartsRefers to the key number of the part Check to see if it has been pre-assembledX 3 1/4 Bolt 16 x 1 3/4 Bolt2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference X 8 Bolt R0600AQty Description 16 x 1 BoltExploded DRAWING-Model No. WESY8630C3