Healthrider WESY8630C3 Important Precautions, Read all instructions in this manual, Decal shown

Page 3

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read the following important precautions before using the training system.

1.It is the responsibility of the owner to ensure that all users of the training system are ade- quately informed of all precautions.

2.Read all instructions in this manual and in

the accompanying literature before using the training system.

3.Use the training system only on a level sur- face. Place a mat beneath the training sys- tem to protect the floor or carpet.

4.Inspect and tighten all parts often. Replace any worn parts immediately.

5.Keep children under the age of 12 and pets away from the training system at all times.

6.Never release the press arm, butterfly arms, leg lever, leg press plate, lat bar, ab strap, or nylon strap while weights are raised. The weights will fall with great force.

7.Keep hands and feet away from moving parts.

8.Always wear athletic shoes for foot protec- tion.

9.Always stand on the foot plate when per-

forming an exercise that could cause the training system to tip.

10.When using the leg press station, always be sure that the lock pin is fully inserted and that the lock pin is clipped in place on the

adjustment tube (see page 23).

11.Make sure that the cables remain on the pul-

leys at all times. If the cables bind while you are exercising, stop immediately and make

sure that the cables are on all of the pulleys.

12. Always disconnect the lat bar from the train

-

 

 

ing system when performing an exercise that

 

 

 

does not use the lat bar

.

 

 

 

 

 

 

 

 

13.If you feel pain or dizziness at any time while exercising, stop immediately and begin cool- ing down.

14.The training system is intended for home use only. Do not use the training system in any commercial, rental, or institutional setting.

15.The decal shown

at the right has been attached to the training sys- tem in the two locations shown on page 4. If a decal is missing or illegible, please call toll- free 1-888-936- 4266 to order a free replacement decal. Apply the decal in the loca- tion shown.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

3

Image 3
Contents Customer HOT Line QUESTIONS?Model No. WESY8630C3 Serial No Serial Number Decal Under SeatLimited Warranty Table of ContentsDecal shown Important PrecautionsRead all instructions in this manual Sure that the cables are on all of the pulleysBefore YOU Begin Using the WeiderAssembly Frame Assembly BAG TWO Be sure that the pin Stack of WeightsBe sure that the pins on Do not over Tighten the Nylon LocknutLocknuts used in steps 1 through Do not tighten Nylon Locknuts yetNylon Locknut As shownShown Be sure that Right Arm 5. Be sure that the upperOnly once Order new RetainersOnto the Bolt, but do not fully tighten it Identify the Butterfly Cable 89-this isBut PulleyPulley Plates 31 and 3 1/2 Pulleys Groove of the PulleyPre-assembled Shortest CableBolt, but do not fully tighten it. Leave Sure that the Cable Trap is insideBase 13 with a 3/8 x 2 Bolt 50 and a 3/8 Cable Trap is turned to hold the Cable in placeDirection shown PlaceUpper Pulley move smoothly Be sure that Large Cable Trap is turned to holdBolt 76, a 3/8 Washer 38, and a 3/8 Nylon Locknut 3/8 x 5 Bolt 74 and the 3/8 Nylon LocknutPivot Identify the High Cable 85-this is High Cable around a 3 1/2 Pulley 82. AttachIndicated side Nylon Locknut 42. Do not overtightenBe sure that the Cable Trap is in the indi- cated position With the Bolt and a 5/16 Nylon Locknut Press a 1 1/2 Square Inner Cap 57 into the Rear Seat FrameSeat Plate to the Seat 17 with two 1/4 x 3/4 Screws Press a 1 1/2 Square Inner Cap 57 into the Leg LeverPress two 3/4 Round Inner Caps 78 into each Pad Tube TROUBLE-SHOOTING and Maintenance onAttaching the LAT BAR or Nylon Strap to LOW Pulley Station HOW to USE the Training SystemChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to High Pulley StationAttaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateStation Attaching and Removing the SeatLbs Weight Resistance ChartRear Cable 87 can be tightened in the same manner TROUBLE-SHOOTING and MaintenanceTightening the Cables See drawing 1. Remove the 3/8 Nylon Locknut 42Butterfly Cable Cable DiagramsLong U Bracket Low PulleyTop Frame High CablePart No R0600A Ordering Replacement PartsRefers to the key number of the part Check to see if it has been pre-assembledX 3 1/4 Bolt 16 x 1 3/4 Bolt2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference X 8 Bolt R0600AQty Description 16 x 1 BoltExploded DRAWING-Model No. WESY8630C3