Healthrider WESY8630C3 manual Do not over Tighten the Nylon Locknut, Be sure that the pin

Page 7

FRAME ASSEMBLY

4. Slide the Front Seat Frame (8) onto the indi-

 

4

 

40

cated 5/16” x 2 1/2” Carriage Bolts (49) in the

 

55

 

 

 

Press Base (13). Hand tighten two 5/16”

 

 

 

 

 

 

8

Nylon Locknuts (40) onto the Carriage Bolts.

 

20

 

 

 

 

 

 

Attach the other end of the Front Seat Frame

 

 

4

56

(8) to the Leg Press Upright (4) with two 5/16”

 

 

 

 

x 2 3/4” Bolts (55), two 5/16” Washers (20),

 

 

 

and two 5/16” Nylon Locknuts (40).

 

 

 

40

 

 

 

 

 

13

Press a 2” Square Inner Cap (56) into the

 

 

 

 

Front Seat Frame (8).

 

 

 

 

 

 

 

 

 

49

5. Insert two Weight Guides (23) into one of the

 

 

 

 

brackets on the Weight Base (14). Attach the

 

5

 

 

lower ends of the Weight Guides with a 5/16”

 

 

 

 

x 6” Bolt (67), two 1/2” x 3/4” Spacers (69),

 

 

 

and a 5/16” Nylon Locknut (40).

Do not over-

 

 

 

tighten the Nylon Locknut.

 

 

 

23

 

 

 

 

 

Attach the other Weight Guides (23) in the

 

23

 

 

 

 

 

 

same manner.

 

 

 

 

 

 

 

 

40

 

 

 

 

 

14

69

67

6. Slide a Weight Bumper (27) onto each of the

 

6

 

90

Weight Guides (23).

 

 

 

Slide eight Weights (90) onto each set of

 

90

 

Pin

 

 

 

Grooves

Weight Guides (23).

Be sure that the pin

 

 

 

 

 

grooves are on the indicated side of each

 

Pin

 

27

stack of Weights.

 

 

 

 

 

Grooves

 

 

 

 

 

27

 

 

 

 

 

 

23

23

 

 

 

 

 

7. Press a Weight Tube Bumper (26) into each

 

7

 

25

Weight Tube (25).

 

 

 

 

 

 

 

Insert a Weight Tube (25) into each stack of

 

 

 

26

Weights (90).

Be sure that the pins on the

 

 

Weight Tubes are in the pin grooves in the

 

 

 

 

upper Weights.

 

 

90

 

90

 

 

 

 

 

7

Image 7
Contents Customer HOT Line QUESTIONS?Model No. WESY8630C3 Serial No Serial Number Decal Under SeatLimited Warranty Table of ContentsDecal shown Important PrecautionsRead all instructions in this manual Sure that the cables are on all of the pulleysBefore YOU Begin Using the WeiderAssembly Frame Assembly BAG TWO Be sure that the pin Stack of WeightsBe sure that the pins on Do not over Tighten the Nylon LocknutLocknuts used in steps 1 through Do not tighten Nylon Locknuts yetAs shown Nylon LocknutShown Be sure that Right Arm 5. Be sure that the upperOnly once Order new RetainersOnto the Bolt, but do not fully tighten it Identify the Butterfly Cable 89-this isBut PulleyPulley Plates 31 and 3 1/2 Pulleys Groove of the PulleyPre-assembled Shortest CableBolt, but do not fully tighten it. Leave Sure that the Cable Trap is insideBase 13 with a 3/8 x 2 Bolt 50 and a 3/8 Cable Trap is turned to hold the Cable in placePlace Direction shownUpper Pulley move smoothly Be sure that Large Cable Trap is turned to holdBolt 76, a 3/8 Washer 38, and a 3/8 Nylon Locknut 3/8 x 5 Bolt 74 and the 3/8 Nylon LocknutPivot Identify the High Cable 85-this is High Cable around a 3 1/2 Pulley 82. AttachIndicated side Nylon Locknut 42. Do not overtightenBe sure that the Cable Trap is in the indi- cated position With the Bolt and a 5/16 Nylon Locknut Press a 1 1/2 Square Inner Cap 57 into the Rear Seat FrameSeat Plate to the Seat 17 with two 1/4 x 3/4 Screws Press a 1 1/2 Square Inner Cap 57 into the Leg LeverPress two 3/4 Round Inner Caps 78 into each Pad Tube TROUBLE-SHOOTING and Maintenance onAttaching the LAT BAR or Nylon Strap to LOW Pulley Station HOW to USE the Training SystemChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to High Pulley StationAttaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateStation Attaching and Removing the SeatLbs Weight Resistance ChartRear Cable 87 can be tightened in the same manner TROUBLE-SHOOTING and MaintenanceTightening the Cables See drawing 1. Remove the 3/8 Nylon Locknut 42Butterfly Cable Cable DiagramsLong U Bracket Low PulleyTop Frame High CablePart No R0600A Ordering Replacement PartsRefers to the key number of the part Check to see if it has been pre-assembledX 3 1/4 Bolt 16 x 1 3/4 Bolt2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference X 8 Bolt R0600AQty Description 16 x 1 BoltExploded DRAWING-Model No. WESY8630C3