Suunto VYTEC DS manual Dive Parameter Settings 1 SET Dive

Page 54

OK

Fig. 4.23. Setting Altitude adjustment. Press scroll buttons to change altitude mode.

OK

Fig. 4.24 Setting Personal adjustment. Press scroll buttons to change personal mode.

OK

Fig. 4.25 Setting RGBM adjustment. Press scroll buttons to change setting.

4.3.1.Dive Parameter Settings [1 SET DIVE]

To enter the Dive Parameter Setting Mode select MODE- 3 SET- 1 SET DIVE. The Dive Parameter Setting mode has two to four op- tions depending on the dive computer mode. In Gauge mode there are two options, in Air mode three options and in Nitrox mode four options.

4.3.1.1Altitude Adjustment, Personal Adjustment, RGBM Set- tings and Safety Stop/ Deep Stop [1 AdJ MODE]

The current Altitude and Personal Adjustment modes are shown when diving and at the sur- face. If the mode does not match the altitude or personal conditions (see section 3.8. “High Altitude Dives and Personal Adjustment”), it is imperative that you enter the correct selec- tion before diving. Use the Altitude Adjustment to select the correct altitude mode. Use the Personal Adjustment to add an extra level of conservatism.

For certain divers and diving conditions you may want to set attenuated RGBM mode When this selection is made it is indicated with a con- tinuously displayed Diver Attention Symbol. The options are full RGBM effects (RGB100), and attenuated RGBM (RGB50).

The deepstop setting allows the user to choose between traditional safety stops or deep stops. If deep stops are set to OFF, traditional safety stop calculation is used. If set to ON itera- tive Deepstops will be prompted instead. The length of the individual deepstops can be set to 1 or 2 minutes.

To enter the Altitude Adjustment, Personal Ad- justment and RGBM effect Setting mode, se- lect MODE- 3 SET- 1 SET DIVE- 1 AdJ MODE.

52

Image 54
Contents Suunto Vytec DS Guide Reference Quick Definition of WARNINGS, Cautions and Notes COPYRIGHT, Trademark and Patent NoticePrEN Page Page Page Table of Contents AIR/NITROX/GAUGE Introduction Suunto RGBM/ Deep Stop AlgorithmSafety Precautions Emergency AscentsNitrox Getting AcquaintedDive Computer Limitations FunctionsMaking the Vytec personal Push ButtonsPress the Smart Mode button Water ContactsWireless Cylinder Pressure Transmission Installing the TransmitterPairing and Code Selection Transmission Data Fail Pressure Transmission Related DisplaysSetc LobtDiving with the Vytec Before DivingActivation and Prechecks Battery Indication Battery Power IndicatorBattery Power Indicator Lowbat +Wireless Transmitter Battery Indicator Dive Planning PlanDive Numbering Shown During Dive Planning User Definable Functions and Alarms Safety StopsRecommended Safety Stop Mandatory Safety Stop Diving display. Pres- ent depth is 19.3 mDiving in AIR Mode Deep StopsBasic Dive Data Bookmark Cylinder Pressure DataConsumed Bottom Time CBT Ascent Rate Indicator Ascent Rate IndicatorSafety Stops and Deep Stops Decompression divesCEILING, Ceiling ZONE, Floor Decompression Range Display below the Floor Display Above the FloorDisplay AT the Ceiling Zone Diving in Nitrox Mode 3.4.1. Before Diving Display Above the CeilingDefault Nitrox Settings Oxygen Displays22. Diving in Nitrox mode. The O2% is set to 32% Oxygen Limit Fraction OLFGas Change, Multiple Breathing Gas Mixes Diving in Gauge Mode AT the Surface 3.6.1. Surface Interval Dive Numbering Separated by a colon, tellingFlying After Diving Audible and Visual Alarms Three double beeps occur, whenOxygen Alarms in Nitrox Mode Set oxygen partial pressure limit is exceeded. The maximumPersonal Adjustment High Altitude Dives and Personal AdjustmentAltitude Adjustment Altitude Adjustment RangesPersonal Adjustment Ranges Error Conditions Rgbm Model SettingsOmitted Decompression Menu Based Modes USE of the Menu Based FunctionsExit / Quit List of the Menu Based ModesMemories and Data Transfer 1 Memory Logbook and Dive Profile Memory 1 LogbookI, main display Fig III Fig Dive History Memory 2 History Dive Profile Memory ProfData Transfer and PC-Interface 3 TR-PC Simulation Mode 2 Simul Dive Simulator 1 SimdiveDive Planning Simulator 2 Simplan SET Modes 3 SETDive Parameter Settings 1 SET Dive Dive Time Alarm Setting 2 d Alarm Maximum Depth Alarm Setting 3 MAX DpthNitrox/Oxygen Settings 4 Nitrox Setting Time 2 SET Time Adjusting Time 1 AdJ TimeSetting Preferences 3 SET Pref Adjusting Date 2 AdJ DateAdjusting Daily Alarm 3 T Alarm Backlight Setting 1 LightProfile Sample Rate Setting 4 REC Dive Computer Units Setting 2 UnitsWireless Transmission Settings 3 HP Dive Computer Model Setting 5 ModelCare of Your Dive Computer Care and MaintenanceImportant Information Water Contacts and Push ButtonsMaintenance Water Resistance InspectionBattery Replacement 5.5.1. Computer battery Battery KITBattery Replacement Tools RequiredPage Wireless Transmitter Battery Replacement Opening of the securing ringTransmitter Battery Replacement Tools RequiredTechnical Description Operating PrinciplesNO-DECOMPRESSION Limits Altitude Diving Suunto Reduced Gradient Bubble Model Rgbm Surface IntervalsOxygen Exposure Technical Specification TransmitterOther displays Battery Vytec Warranty SUUNTOSPORTS.COM System RequirementsMy Suunto CommunitiesSport Forums Getting StartedGlossary EAD EANNo DEC Time NitroxNoaa OLFPO2 RgbmSurf Time Tissue group Disposal of the Device TIME-KEEPING and STAND-BY Mode Page Page Made in Finland Suunto Oy 01 / 2004, 08