JVC RX-730R manual Connecting the rear and center speakers, Connecting the subwoofer speaker

Page 12

English

Connecting the rear and center speakers

Cut, twist and remove the insulation at the end of each speaker signal cable first, and then, connect rear speakers to the REAR SPEAKERS terminals and a center speaker to the CENTER SPEAKER terminals by using the cables.

		1 Open the terminal and
			then insert the speaker
			signal cable.
	CENTER	REAR
	SPEAKER	SPEAKERS
	RIGHT	LEFT
Center Speaker
Left Rear Speaker	Right Rear Speaker	2	Close the terminal.
Left Rear Speaker	Right Rear Speaker

Notes:

•You can register the center speaker size after you finish its connection. If you register it, you do not have to set the center speaker mode when setting the surround mode.

(If you do not use a center speaker, register that information.) See page 17.

•When you connect rear speakers, make sure that both left and right speakers are connected; otherwise, no sound will come out of the rear speakers.

Connecting the subwoofer speaker

You can enhance the bass by connecting a subwoofer.

Connect the input jack of a powered subwoofer to the SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs.

SUBWOOFER

OUT

Powered subwoofer

Page 7

Image 12

Contents RX-730RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-730RBK Table of Contents Before Installation Checking the Supplied AccessoriesGetting Started Switches, Buttons and Controls Front PanelFront Panel Remote Control How to open the outside panelRemote Control Outside panel Outside panelConnecting the FM and AM MW/LW Antennas Using the Supplied FM AntennaFM Antenna Connections AM MW/LW Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the rear and center speakers Connecting the subwoofer speakerOpen the terminal Close the terminalCase 1 When you connect only front speakers Case 2 When you connect front speakers and a center speakerCase 3 When you connect front and rear speakers About the speaker impedance of the speakersConnecting Audio/Video Components Audio component connectionsAudio Components Video Components If your audio components have a Compu LINK-3 terminalVideo component connections VCRConnecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet Press Power to set it in the on positionTurning the Power On and Off Basic OperationsSelecting the Source to Play Adjusting the Volume From the remote controlSelecting the Front Speakers On the front panel onlyListening with Headphones From the remote control onlyMute appears on the display and the volume turns off Muting the SoundBasic Settings Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness From the remote control Press Balance L/R -/+Using the Sleep Timer To cancel the Sleep TimerFrom the remote control Press Sleep repeatedly Selecting the Center Speaker Size Large SmallLarge SmallUsing Visual Confirmation ExamplesUsing the One Touch Operation To store the sound settings Press ONE Touch OperationTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningStoring the preset stations Receiving Radio BroadcastsSelecting the FM Reception Mode Tuning in a preset stationAuto MonoAssigning Names to Preset Stations Using the RDS Radio Data System to Receive FM Stations What Information Can RDS Signals Provide?PTY Searching for a Program by PTY Codes Alarm NewsAffairs InfoSwitching to a Broadcast Program of Your Choice Temporarily TA NEWS/INFO TA/INFO TA/NEWSNews Info TA/NEWS/INFO CaseUsing the SEA Modes Selecting Your Favorite SEA ModeRock Musical Movie Country SEA OFF Usermode Jazz Creating Your Own SEA Mode Adjust the SEA frequency and its levelTo recall your own SEA adjustment To erase a stored adjustmentUsing the Surround Processor Using JVC’s Hall SurroundWhat is surround? Prologic 3CHLOGIC Hall Surr OFFDelay Delay 1 Delay Delay 4 DelayDelay Press Delay to adjust the delay timeSpeaker Arrangements for Dolby Surround This casePreparing for Dolby Surround Wide Normal PhantomIf necessary, adjust the speaker output level as follows SOFT2 SOFT1 Flat SHARP1 SHARP2 Press Test to start checking the speaker output balance Press Test again to stop the test toneUsing Dolby Surround Using the On-Screen Display to Control the Receiver From the remote control Press MenuPress %/ Þto move To SETTING, then press @ / # Press %/ Þto move to SOURCE, then press @/ #Listening at Low Volume Loudness Also see Press %/ Þ to move To SEA Adjust then press @ / # Press %/ Þ / @ / #to adjust the SEA mode as you wantPress %/ Þto move to TUNER, then press @ / # Press %/ Þto move to SEA, then press @ / #Press %/ Þto move to Surround ADJUST, then press @ / # Press %/ Þto move To SURROUND, then press @/ #Press %/ Þto move to one of the surround modes For Dolby 3ch LogicCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingUsing the Remote Control To operate JVC audio components using this remote controlTuner Sound control section AmplifierCD player CD player-changerCassette deck TurntableTo operate JVC video components using this remote control Preset Channel +0, +10 Selects the TV channels Enter button after selecting a channel numberSimplifying the Operations Using the Remote Control Programing a series of operationsPress Cancel Erasing a programRepeat until you program up to 16 steps Storing the signals Open the outside panel of this remote controlPress one of the buttons on the remote mode section Operating the Other Manufacturers’ Audio/Video ComponentsUsing stored signals Press Learn to finish the storing procedureErasing stored signals Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierVideo FM tuner IHF AM MW/LW tunerGeneral EN, GE, FR, NL, SP, IT 0697OFYOTKJEM