JVC RX-730R manual Simplifying the Operations Using the Remote Control

Page 50

English

Simplifying the Operations Using the Remote Control

You can program and store a series of operations in a specific order you want. After making a program, you can perform these programed operations at a press of the SEQUENTIAL PROGRAM KEY.

Programing a series of operations

LEARN CANCEL

Remote: Inside

SEQUENTIAL PROGRAM KEY

You can make 3 different programs, each containing up to 16 steps.

1Open the outside panel of the remote control.

2Press LEARN so that the SEND/LEARN indicator lights up (green).

Lights

SEND/LEARN ERROR

3Close the outside panel.

4Press SEQUENTIAL PROGRAM KEY A, B, or C to which you want to assign a program you are making from now.

A	B	C	The SEND/LEARN indicator starts flashing.
			The SEND/LEARN indicator starts flashing.
			Flashes	ERROR
			SEND/LEARN	ERROR

Remote: Outside	Note:
	Note:
	If the ERROR indicator lights up (red) while the SEND/LEARN indicator is flashing, you have already
	assigned a program to that SEQUENTIAL PROGRAM KEY. To add steps to the program, continue to step
	5. If you do not want to change it, press another SEQUENTIAL PROGRAM KEY after the SEND/LEARN
	indicator stops flashing.

5While the SEND/LEARN indicator is flashing, press the button you want to store as the first step of the program.

Both the SEND/LEARN and ERROR indicators light up, and then only the ERROR indicator goes off.

			SEND/LEARN		ERROR
Lights									Lights
			SEND/LEARN
					ERROR

Lights

SEND/LEARN ERROR

When the SEND/LEARN indicator goes off and starts flashing again, the first step is stored.

The ERROR indicator lights up while the SEND/LEARN indicator is flashing.

SEND/LEARN ERROR

Flashes								Lights
Flashes								Lights

SEND/LEARN ERROR

Note:

If the SEND/LEARN indicator stops flashing before you press the button, repeat from step 4 again.

Page 45

Image 50

Contents RX-730RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-730RBK Table of Contents Getting Started Before InstallationChecking the Supplied Accessories Front Panel Switches, Buttons and ControlsFront Panel Remote Control Outside panel Remote ControlHow to open the outside panel Outside panelFM Antenna Connections Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna AM MW/LW Antenna ConnectionsConnecting the Speakers Connecting the front speakersOpen the terminal Connecting the rear and center speakersConnecting the subwoofer speaker Close the terminalCase 3 When you connect front and rear speakers Case 1 When you connect only front speakersCase 2 When you connect front speakers and a center speaker About the speaker impedance of the speakersAudio Components Video Components Connecting Audio/Video ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalVideo component connections VCRPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control Press Power to set it in the on positionSelecting the Source to Play Turning the Power On and OffBasic Operations Selecting the Front Speakers Adjusting the VolumeFrom the remote control On the front panel onlyMute appears on the display and the volume turns off Listening with HeadphonesFrom the remote control only Muting the SoundListening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance From the remote control Press Balance L/R -/+From the remote control Press Sleep repeatedly Using the Sleep TimerTo cancel the Sleep Timer Large Selecting the Center Speaker SizeLarge Small SmallUsing Visual Confirmation ExamplesTo cancel the One Touch Operation function Using the One Touch OperationTo store the sound settings Press ONE Touch Operation One Touch OperationStoring the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsAuto Selecting the FM Reception ModeTuning in a preset station MonoAssigning Names to Preset Stations PTY Using the RDS Radio Data System to Receive FM StationsWhat Information Can RDS Signals Provide? Searching for a Program by PTY Codes Affairs AlarmNews InfoNews Info TA/NEWS/INFO Switching to a Broadcast Program of Your Choice TemporarilyTA NEWS/INFO TA/INFO TA/NEWS CaseRock Musical Movie Country SEA OFF Usermode Jazz Using the SEA ModesSelecting Your Favorite SEA Mode To recall your own SEA adjustment Creating Your Own SEA ModeAdjust the SEA frequency and its level To erase a stored adjustmentWhat is surround? Using the Surround ProcessorUsing JVC’s Hall Surround Prologic 3CHLOGIC Hall Surr OFFDelay DelayDelay 1 Delay Delay 4 Delay Press Delay to adjust the delay timeSpeaker Arrangements for Dolby Surround This casePreparing for Dolby Surround Wide Normal PhantomIf necessary, adjust the speaker output level as follows SOFT2 SOFT1 Flat SHARP1 SHARP2 Press Test to start checking the speaker output balance Press Test again to stop the test toneUsing Dolby Surround Press %/ Þto move To SETTING, then press @ / # Using the On-Screen Display to Control the ReceiverFrom the remote control Press Menu Press %/ Þto move to SOURCE, then press @/ #Listening at Low Volume Loudness Also see Press %/ Þto move to TUNER, then press @ / # Press %/ Þ to move To SEA Adjust then press @ / #Press %/ Þ / @ / #to adjust the SEA mode as you want Press %/ Þto move to SEA, then press @ / #Press %/ Þto move to one of the surround modes Press %/ Þto move to Surround ADJUST, then press @ / #Press %/ Þto move To SURROUND, then press @/ # For Dolby 3ch LogicAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingTuner Using the Remote ControlTo operate JVC audio components using this remote control Sound control section AmplifierCassette deck CD playerCD player-changer Turntable0, +10 Selects the TV channels To operate JVC video components using this remote controlPreset Channel + Enter button after selecting a channel numberSimplifying the Operations Using the Remote Control Programing a series of operationsRepeat until you program up to 16 steps Press CancelErasing a program Press one of the buttons on the remote mode section Storing the signalsOpen the outside panel of this remote control Operating the Other Manufacturers’ Audio/Video ComponentsUsing stored signals Press Learn to finish the storing procedureErasing stored signals Troubleshooting Problem Possible Cause SolutionVideo SpecificationsAmplifier General FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT 0697OFYOTKJEM