JVC RX-730R manual Getting Started, Before Installation, Checking the Supplied Accessories

Page 7

Getting Started

This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply.

Before Installation

General

•Be sure your hands are dry.

•Turn the power off to all components.

•Read the manuals supplied with the components you are going to connect.

Locations

•Install the receiver in a location that is level and protected from moisture.

•The temperature around the receiver must be between –5˚ and 35˚ C (23˚ and 95˚ F).

•Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

Handling the receiver

•Do not insert any metal object into the receiver.

•Do not disassemble the receiver or remove screws, covers, or cabinet.

•Do not expose the receiver to rain or moisture.

Checking the Supplied Accessories

Check to be sure you have all of the following items, which are supplied with the receiver.

The number in the parenthesis indicates the quantity of the pieces supplied.

•Remote Control (1)

•Batteries (2)

•AM (MW/LW) Loop Antenna (1)

•FM Antenna (1)

If anything is missing, contact your dealer immediately.

English

Page 2

Image 7

Contents RX-730RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-730RBK Table of Contents Checking the Supplied Accessories Before InstallationGetting Started Front Panel Switches, Buttons and ControlsFront Panel Outside panel Remote ControlHow to open the outside panel Remote Control Outside panelAM MW/LW Antenna Connections Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna FM Antenna ConnectionsConnecting the front speakers Connecting the SpeakersClose the terminal Connecting the rear and center speakersConnecting the subwoofer speaker Open the terminalAbout the speaker impedance of the speakers Case 1 When you connect only front speakersCase 2 When you connect front speakers and a center speaker Case 3 When you connect front and rear speakersIf your audio components have a Compu LINK-3 terminal Connecting Audio/Video ComponentsAudio component connections Audio Components Video ComponentsVCR Video component connectionsPress Power to set it in the on position Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletBasic Operations Turning the Power On and OffSelecting the Source to Play On the front panel only Adjusting the VolumeFrom the remote control Selecting the Front SpeakersMuting the Sound Listening with HeadphonesFrom the remote control only Mute appears on the display and the volume turns offFrom the remote control Press Balance L/R -/+ Basic SettingsAdjusting the Front Speaker Output Balance Listening at Low Volume LoudnessTo cancel the Sleep Timer Using the Sleep TimerFrom the remote control Press Sleep repeatedly Small Selecting the Center Speaker SizeLarge Small LargeExamples Using Visual ConfirmationOne Touch Operation Using the One Touch OperationTo store the sound settings Press ONE Touch Operation To cancel the One Touch Operation functionReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Storing the preset stationsMono Selecting the FM Reception ModeTuning in a preset station AutoAssigning Names to Preset Stations What Information Can RDS Signals Provide? Using the RDS Radio Data System to Receive FM StationsPTY Searching for a Program by PTY Codes Info AlarmNews AffairsCase Switching to a Broadcast Program of Your Choice TemporarilyTA NEWS/INFO TA/INFO TA/NEWS News Info TA/NEWS/INFOSelecting Your Favorite SEA Mode Using the SEA ModesRock Musical Movie Country SEA OFF Usermode Jazz To erase a stored adjustment Creating Your Own SEA ModeAdjust the SEA frequency and its level To recall your own SEA adjustmentPrologic 3CHLOGIC Hall Surr OFF Using the Surround ProcessorUsing JVC’s Hall Surround What is surround?Press Delay to adjust the delay time DelayDelay 1 Delay Delay 4 Delay DelayThis case Speaker Arrangements for Dolby SurroundWide Normal Phantom Preparing for Dolby SurroundIf necessary, adjust the speaker output level as follows SOFT2 SOFT1 Flat SHARP1 SHARP2 Press Test again to stop the test tone Press Test to start checking the speaker output balanceUsing Dolby Surround Press %/ Þto move to SOURCE, then press @/ # Using the On-Screen Display to Control the ReceiverFrom the remote control Press Menu Press %/ Þto move To SETTING, then press @ / #Listening at Low Volume Loudness Also see Press %/ Þto move to SEA, then press @ / # Press %/ Þ to move To SEA Adjust then press @ / #Press %/ Þ / @ / #to adjust the SEA mode as you want Press %/ Þto move to TUNER, then press @ / #For Dolby 3ch Logic Press %/ Þto move to Surround ADJUST, then press @ / #Press %/ Þto move To SURROUND, then press @/ # Press %/ Þto move to one of the surround modesSynchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionSound control section Amplifier Using the Remote ControlTo operate JVC audio components using this remote control TunerTurntable CD playerCD player-changer Cassette deckEnter button after selecting a channel number To operate JVC video components using this remote controlPreset Channel + 0, +10 Selects the TV channelsPrograming a series of operations Simplifying the Operations Using the Remote ControlErasing a program Press CancelRepeat until you program up to 16 steps Operating the Other Manufacturers’ Audio/Video Components Storing the signalsOpen the outside panel of this remote control Press one of the buttons on the remote mode sectionPress Learn to finish the storing procedure Using stored signalsErasing stored signals Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsVideo AM MW/LW tuner FM tuner IHFGeneral EN, GE, FR, NL, SP, IT 0697OFYOTKJEM