JVC RX-730R manual Using the SEA Modes, Selecting Your Favorite SEA Mode

Page 32

English

Using the SEA Modes

The SEA (Sound Effect Amplifier) modes give you control of the way your music sounds.

Note:

The SEA modes cannot be used for recording.

See also page 39.

MENU

Selecting Your Favorite SEA Mode

SEA MODE

Front panel

SEA

MODE

Remote: Outside

On the front panel:

1.Press SEA MODE so that the Control % / Þbuttons work for selecting the SEA mode. The lamp next to the button lights up.

2.Press Control %/ Þuntil the mode you want appears on the display. Each time you press the button, the SEA mode changes as follows:

ROCKMUSICALMOVIECOUNTRY

SEA OFF USERMODE JAZZ

Note:

When the SEA mode is turned on, the SEA indicator lights up on the display.

ROCK:	Gives a heavy sound. Both high and low frequencies are boosted.

MUSICAL:	Enhance the mid-frequency range, which the human voice is mostly made up of.

MOVIE:	Adds breadth to sounds so you feel like you are in a movie theater.

COUNTRY:	Enhances the high-frequency range so that instruments such the violin and banjo
	are emphasized.

JAZZ:	Gives a feeling of a live atmosphere. Good for acoustic music.

USERMODE:	Your original SEA adjustment (see page 28).

SEA OFF:	No SEA mode is applied (see below).

To cancel the SEA mode, press Control % / Þuntil “SEA OFF” appears in step 2 above. The SEA indicator goes off from the display.

From the remote control:

Press SEA MODE repeatedly until the SEA mode you want appears on the display.

Each time you press the button, the SEA mode changes as follows:

ROCK MUSICAL MOVIE COUNTRY

SEA OFF USERMODE JAZZ

Note:

When the SEA mode is turned on, the SEA indicator lights up on the display.

To cancel the SEA mode, press SEA MODE repeatedly until “SEA OFF” appears on the display. The SEA indicator goes off from the display.

Page 27

Image 32

Contents RX-730RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-730RBK Table of Contents Getting Started Before InstallationChecking the Supplied Accessories Front Panel Switches, Buttons and ControlsFront Panel Remote Control How to open the outside panelRemote Control Outside panel Outside panelConnecting the FM and AM MW/LW Antennas Using the Supplied FM AntennaFM Antenna Connections AM MW/LW Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the rear and center speakers Connecting the subwoofer speakerOpen the terminal Close the terminalCase 1 When you connect only front speakers Case 2 When you connect front speakers and a center speakerCase 3 When you connect front and rear speakers About the speaker impedance of the speakersConnecting Audio/Video Components Audio component connectionsAudio Components Video Components If your audio components have a Compu LINK-3 terminalVideo component connections VCRConnecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet Press Power to set it in the on positionSelecting the Source to Play Turning the Power On and OffBasic Operations Adjusting the Volume From the remote controlSelecting the Front Speakers On the front panel onlyListening with Headphones From the remote control onlyMute appears on the display and the volume turns off Muting the SoundBasic Settings Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness From the remote control Press Balance L/R -/+From the remote control Press Sleep repeatedly Using the Sleep TimerTo cancel the Sleep Timer Selecting the Center Speaker Size Large SmallLarge SmallUsing Visual Confirmation ExamplesUsing the One Touch Operation To store the sound settings Press ONE Touch OperationTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningStoring the preset stations Receiving Radio BroadcastsSelecting the FM Reception Mode Tuning in a preset stationAuto MonoAssigning Names to Preset Stations PTY Using the RDS Radio Data System to Receive FM StationsWhat Information Can RDS Signals Provide? Searching for a Program by PTY Codes Alarm NewsAffairs InfoSwitching to a Broadcast Program of Your Choice Temporarily TA NEWS/INFO TA/INFO TA/NEWSNews Info TA/NEWS/INFO CaseRock Musical Movie Country SEA OFF Usermode Jazz Using the SEA ModesSelecting Your Favorite SEA Mode Creating Your Own SEA Mode Adjust the SEA frequency and its levelTo recall your own SEA adjustment To erase a stored adjustmentUsing the Surround Processor Using JVC’s Hall SurroundWhat is surround? Prologic 3CHLOGIC Hall Surr OFFDelay Delay 1 Delay Delay 4 DelayDelay Press Delay to adjust the delay timeSpeaker Arrangements for Dolby Surround This casePreparing for Dolby Surround Wide Normal PhantomIf necessary, adjust the speaker output level as follows SOFT2 SOFT1 Flat SHARP1 SHARP2 Press Test to start checking the speaker output balance Press Test again to stop the test toneUsing Dolby Surround Using the On-Screen Display to Control the Receiver From the remote control Press MenuPress %/ Þto move To SETTING, then press @ / # Press %/ Þto move to SOURCE, then press @/ #Listening at Low Volume Loudness Also see Press %/ Þ to move To SEA Adjust then press @ / # Press %/ Þ / @ / #to adjust the SEA mode as you wantPress %/ Þto move to TUNER, then press @ / # Press %/ Þto move to SEA, then press @ / #Press %/ Þto move to Surround ADJUST, then press @ / # Press %/ Þto move To SURROUND, then press @/ #Press %/ Þto move to one of the surround modes For Dolby 3ch LogicCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingUsing the Remote Control To operate JVC audio components using this remote controlTuner Sound control section AmplifierCD player CD player-changerCassette deck TurntableTo operate JVC video components using this remote control Preset Channel +0, +10 Selects the TV channels Enter button after selecting a channel numberSimplifying the Operations Using the Remote Control Programing a series of operationsRepeat until you program up to 16 steps Press CancelErasing a program Storing the signals Open the outside panel of this remote controlPress one of the buttons on the remote mode section Operating the Other Manufacturers’ Audio/Video ComponentsUsing stored signals Press Learn to finish the storing procedureErasing stored signals Troubleshooting Problem Possible Cause SolutionVideo SpecificationsAmplifier General FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT 0697OFYOTKJEM