JVC RX-730R manual Using the On-Screen Display to Control the Receiver

Page 42

English

Using the On-Screen Display to Control the Receiver

You can use the menu function on the TV screen to control the receiver.

To use this function, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page 10), and set the TV’s input mode to the appropriate position to which the receiver is connected.

When the TV’s input mode is for TV, you cannot see the on-screen display.

IMPORTANT:

When you use the menu functions, make sure that you have connected a TV and operate the menu function while watching the on-screen displays on the TV.

Basic Procedures

Menu function buttons

MENU

MENU

EXIT

ON SCREEN CONTROL

MAIN MENU

From the remote control:

1.Press MENU.

The MAIN MENU appears on the TV screen.

•If you press % / Þ/ @/ #, a sub-menu you can adjust at that time appears on the TV screen instead of the MAIN MENU.

2.Press % / Þto move to the sub-menu you want to set, then press @ / #. The sub-menu you want appears.

3.If necessary, press % / Þ/ @/ # to set or adjust the item you want on the selected sub- menu.

When a item is selected, the item will be highlighted.

Note:

Moving to an item does not mean that you have selected it. If the item is not highlighted, press @/ # to highlight it.

4.When you finish, press MENU EXIT. The menu disappears from the TV.

To go back to the MAIN MENU any time during the process

Press MENU again.

Shows the buttons you can use on the current menu. In this case, press % / Þ to move up and down, and @ / # to select the item. (The menus are shown on the TV for about one minute.)

Selecting the Source to Play (Also see page 12)

SOURCE menu

1.Press MENU.

The MAIN MENU appears on the TV.

2. Press %/ Þto move to “SOURCE,” then press @/ #.

The SOURCE menu appears.

3. Press %/ Þto move to the source you want to play.

4.When you finish, press MENU EXIT. The menu disappears from the TV.

Adjusting the Front Speaker Output Balance (Also see page 15)

1.Press MENU.

The MAIN MENU appears on the TV.

2. Press %/ Þto move

to “SETTING,” then press @ / #.

The SETTING menu appears.

3.Press %/ Þto move to “BAL.” (Balance).

4.Press @/ # repeatedly to adjust the balance.

5.When you finish, press MENU EXIT. The menu disappears from the TV.

SETTING menu

Shows the buttons you can use on the current menu.

In this case, press % / Þ to

move up and down, and @ / # to adjust or set the item.

Page 37

Image 42

Contents RX-730RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-730RBK Table of Contents Before Installation Checking the Supplied AccessoriesGetting Started Switches, Buttons and Controls Front PanelFront Panel Remote Control Outside panel Remote ControlHow to open the outside panel Outside panelFM Antenna Connections Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna AM MW/LW Antenna ConnectionsConnecting the Speakers Connecting the front speakersOpen the terminal Connecting the rear and center speakersConnecting the subwoofer speaker Close the terminalCase 3 When you connect front and rear speakers Case 1 When you connect only front speakersCase 2 When you connect front speakers and a center speaker About the speaker impedance of the speakersAudio Components Video Components Connecting Audio/Video ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalVideo component connections VCRPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control Press Power to set it in the on positionTurning the Power On and Off Basic OperationsSelecting the Source to Play Selecting the Front Speakers Adjusting the VolumeFrom the remote control On the front panel onlyMute appears on the display and the volume turns off Listening with HeadphonesFrom the remote control only Muting the SoundListening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance From the remote control Press Balance L/R -/+Using the Sleep Timer To cancel the Sleep TimerFrom the remote control Press Sleep repeatedly Large Selecting the Center Speaker SizeLarge Small SmallUsing Visual Confirmation ExamplesTo cancel the One Touch Operation function Using the One Touch OperationTo store the sound settings Press ONE Touch Operation One Touch OperationStoring the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsAuto Selecting the FM Reception ModeTuning in a preset station MonoAssigning Names to Preset Stations Using the RDS Radio Data System to Receive FM Stations What Information Can RDS Signals Provide?PTY Searching for a Program by PTY Codes Affairs AlarmNews InfoNews Info TA/NEWS/INFO Switching to a Broadcast Program of Your Choice TemporarilyTA NEWS/INFO TA/INFO TA/NEWS CaseUsing the SEA Modes Selecting Your Favorite SEA ModeRock Musical Movie Country SEA OFF Usermode Jazz To recall your own SEA adjustment Creating Your Own SEA ModeAdjust the SEA frequency and its level To erase a stored adjustmentWhat is surround? Using the Surround ProcessorUsing JVC’s Hall Surround Prologic 3CHLOGIC Hall Surr OFFDelay DelayDelay 1 Delay Delay 4 Delay Press Delay to adjust the delay timeSpeaker Arrangements for Dolby Surround This casePreparing for Dolby Surround Wide Normal PhantomIf necessary, adjust the speaker output level as follows SOFT2 SOFT1 Flat SHARP1 SHARP2 Press Test to start checking the speaker output balance Press Test again to stop the test toneUsing Dolby Surround Press %/ Þto move To SETTING, then press @ / # Using the On-Screen Display to Control the ReceiverFrom the remote control Press Menu Press %/ Þto move to SOURCE, then press @/ #Listening at Low Volume Loudness Also see Press %/ Þto move to TUNER, then press @ / # Press %/ Þ to move To SEA Adjust then press @ / #Press %/ Þ / @ / #to adjust the SEA mode as you want Press %/ Þto move to SEA, then press @ / #Press %/ Þto move to one of the surround modes Press %/ Þto move to Surround ADJUST, then press @ / #Press %/ Þto move To SURROUND, then press @/ # For Dolby 3ch LogicAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingTuner Using the Remote ControlTo operate JVC audio components using this remote control Sound control section AmplifierCassette deck CD playerCD player-changer Turntable0, +10 Selects the TV channels To operate JVC video components using this remote controlPreset Channel + Enter button after selecting a channel numberSimplifying the Operations Using the Remote Control Programing a series of operationsPress Cancel Erasing a programRepeat until you program up to 16 steps Press one of the buttons on the remote mode section Storing the signalsOpen the outside panel of this remote control Operating the Other Manufacturers’ Audio/Video ComponentsUsing stored signals Press Learn to finish the storing procedureErasing stored signals Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierVideo FM tuner IHF AM MW/LW tunerGeneral EN, GE, FR, NL, SP, IT 0697OFYOTKJEM