JVC RX-730R manual Basic Operations, Turning the Power On and Off, Selecting the Source to Play

Page 17

Basic Operations

The following operations are commonly used when you play any sound source.

Turning the Power On and Off

English

STANDBY

On the front panel:

To turn on the power, press STANDBY/ON .

The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the display.

STANDBY/ON

Current source name appears

100

1k

10k

VOLUME

Volume level is also shown here whenever the power

STANDBY

STANDBY/ON

Front panel

AUDIO

Remote: Outside

is on.

To turn off the power (into standby mode), press STANDBY/ON again.

The STANDBY lamp lights up.

From the remote control:
To turn on the power, press AUDIO	.

The STANDBY lamp goes off. The name of the current source appears on the display.

To turn off the power (into standby mode), press AUDIO again. The STANDBY lamp lights up.

Note:

Pressing STANDBY/ON or AUDIO again turns off the power (into standby mode) and lights the STANDBY lamp. A small amount of power is consumed in standby mode. To turn the power off completely,

press POWER to set it in the ÑOFF position on the front panel.

See also page 37.

MENU

Selecting the Source to Play

You need to select the source before you start playing any source.

	On the front panel:
SOURCE	1. Press SOURCE so that the Control % / Þbuttons work for selecting the source.

2. Press Control %/ Þuntil the source name you want appears on the display.

The selected source lamp also lights up.

Selected source name appears

Front panel

MUTE AUTO		TUNED STEREO		EON	TA NEWS INFO
FM					SLEEP
AM
CH–					MHz
CH–					kHz
			SURROUND PRO LOGIC 3CH LOGIC HALL
			SEA	LOUDNESS
100	1k	10k	VISUAL CONFIRMATION		VOLUME

Page 12

Image 17

Contents RX-730RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-730RBK Table of Contents Getting Started Before InstallationChecking the Supplied Accessories Front Panel Switches, Buttons and ControlsFront Panel How to open the outside panel Remote ControlRemote Control Outside panel Outside panelUsing the Supplied FM Antenna Connecting the FM and AM MW/LW AntennasFM Antenna Connections AM MW/LW Antenna ConnectionsConnecting the front speakers Connecting the SpeakersConnecting the subwoofer speaker Connecting the rear and center speakersOpen the terminal Close the terminalCase 2 When you connect front speakers and a center speaker Case 1 When you connect only front speakersCase 3 When you connect front and rear speakers About the speaker impedance of the speakersAudio component connections Connecting Audio/Video ComponentsAudio Components Video Components If your audio components have a Compu LINK-3 terminalVCR Video component connectionsPutting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet Press Power to set it in the on positionSelecting the Source to Play Turning the Power On and OffBasic Operations From the remote control Adjusting the VolumeSelecting the Front Speakers On the front panel onlyFrom the remote control only Listening with HeadphonesMute appears on the display and the volume turns off Muting the SoundAdjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness From the remote control Press Balance L/R -/+From the remote control Press Sleep repeatedly Using the Sleep TimerTo cancel the Sleep Timer Large Small Selecting the Center Speaker SizeLarge SmallExamples Using Visual ConfirmationTo store the sound settings Press ONE Touch Operation Using the One Touch OperationTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyStoring the preset stations Receiving Radio BroadcastsTuning in a preset station Selecting the FM Reception ModeAuto MonoAssigning Names to Preset Stations PTY Using the RDS Radio Data System to Receive FM StationsWhat Information Can RDS Signals Provide? Searching for a Program by PTY Codes News AlarmAffairs InfoTA NEWS/INFO TA/INFO TA/NEWS Switching to a Broadcast Program of Your Choice TemporarilyNews Info TA/NEWS/INFO CaseRock Musical Movie Country SEA OFF Usermode Jazz Using the SEA ModesSelecting Your Favorite SEA Mode Adjust the SEA frequency and its level Creating Your Own SEA ModeTo recall your own SEA adjustment To erase a stored adjustmentUsing JVC’s Hall Surround Using the Surround ProcessorWhat is surround? Prologic 3CHLOGIC Hall Surr OFFDelay 1 Delay Delay 4 Delay DelayDelay Press Delay to adjust the delay timeThis case Speaker Arrangements for Dolby SurroundWide Normal Phantom Preparing for Dolby SurroundIf necessary, adjust the speaker output level as follows SOFT2 SOFT1 Flat SHARP1 SHARP2 Press Test again to stop the test tone Press Test to start checking the speaker output balanceUsing Dolby Surround From the remote control Press Menu Using the On-Screen Display to Control the ReceiverPress %/ Þto move To SETTING, then press @ / # Press %/ Þto move to SOURCE, then press @/ #Listening at Low Volume Loudness Also see Press %/ Þ / @ / #to adjust the SEA mode as you want Press %/ Þ to move To SEA Adjust then press @ / #Press %/ Þto move to TUNER, then press @ / # Press %/ Þto move to SEA, then press @ / #Press %/ Þto move To SURROUND, then press @/ # Press %/ Þto move to Surround ADJUST, then press @ / #Press %/ Þto move to one of the surround modes For Dolby 3ch LogicRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingTo operate JVC audio components using this remote control Using the Remote ControlTuner Sound control section AmplifierCD player-changer CD playerCassette deck TurntablePreset Channel + To operate JVC video components using this remote control0, +10 Selects the TV channels Enter button after selecting a channel numberPrograming a series of operations Simplifying the Operations Using the Remote ControlRepeat until you program up to 16 steps Press CancelErasing a program Open the outside panel of this remote control Storing the signalsPress one of the buttons on the remote mode section Operating the Other Manufacturers’ Audio/Video ComponentsPress Learn to finish the storing procedure Using stored signalsErasing stored signals Problem Possible Cause Solution TroubleshootingVideo SpecificationsAmplifier General FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT 0697OFYOTKJEM