JVC RX-7010VBK manual Digital connections, Digital input terminals, Digital output terminal

Page 11

Digital connections

This receiver is equipped with four DIGITAL IN terminals — one digital coaxial terminal and three digital optical terminals, and one DIGITAL OUT terminal.

You can connect any digital equipment such as —

DBS tuner,

Digital TV broadcast tuner,

DVD player,

CD player, and

CD recorder.

IMPORTANT:

When connecting the DVD player, digital TV broadcast tuner or DBS tuner using the digital terminals, you also need to connect it to the video jack (either composite video terminal or S-video terminal) on the rear. Without connecting it to the video jack, you can view no playback picture.

After connecting the components using the DIGITAL IN terminals, set the following correctly if necessary.

Set the digital input (DIGITAL IN) terminal setting correctly. For details, see “Digital Input (DIGITAL IN) Terminal Setting” on page 16.

Select the digital input mode correctly. For details, see “Selecting the Analog or Digital Input Mode” on page 16.

Digital input terminals

Digital TV

DVD player

DVD

 

CD player

 

CD recorder

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Digital coaxial cable (not supplied) between digital coaxial terminals

Digital optical cable (not supplied) between digital optical terminals

Notes:

When shipped from the factory, the DIGITAL IN terminals have been set for use with the following components.

DIGITAL 1 (coaxial): For DVD player

DIGITAL 2 (optical): For CD player

DIGITAL 3 (optical): For digital TV broadcast tuner

DIGITAL 4 (optical): For CD recorder

When you want to operate the CD player or CD recorder using the COMPU LINK remote control system, connect the target component also as described in “Analog connections” (see page 6).

When you want to operate the DVD player using the AV COMPU LINK remote control system, connect the DVD player also as described in “Analog connections” (see page 7).

Digital output terminal

CD recorder, etc.

Digital optical cable (not supplied) between digital optical terminals

When the digital recording equipment such as a CD recorder has a digital optical input terminal, connecting it to the DIGITAL OUT terminal enables you to perform

digital-to-digital recording.DOLBY DIGITAL/PCM

/DTS

DIGITAL OUT

When the component has a digital coaxial output terminal, connect it to the DIGITAL 1 (DVD) terminal, using the digital coaxial cable (not supplied).

When the component has a digital optical output terminal, connect it to the DIGITAL 2 (CD), DIGITAL 3 (TV), or DIGITAL 4 (CDR) terminal, using the digital optical cable (not supplied).

Before connecting a digital optical cable, unplug the protective plug.

DIGITAL 1 (DVD)

DIGITAL 2 ( CD )

DIGITAL 3 ( TV )

DIGITAL 4 (CDR)

DIGITAL IN

8

Image 11
Contents RX-7010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents Front Panel Remote ControlEx. When you press CD button Parts IdentificationGetting Started Before InstallationConnecting the FM and AM Antennas Checking the Supplied AccessoriesAM Antenna Connections Connecting the SpeakersBasic connecting procedure Connecting the front speakersAbout the speaker impedance Connecting Audio/Video ComponentsConnecting the subwoofer speaker Connecting the rear and center speakersCassette deck or CD recorder CD playerTo audio output Video component connectionsDBS tuner TV and/or DBS tunerTo audio OutputDigital output terminal Digital connectionsDigital input terminals R6PSUM-3/AA15F Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletSelecting the Source to Play Turning the Power On and Off StandbyBasic Operations Selecting different sources for picture and sound Adjusting the VolumeListening only with headphones Selecting the Front SpeakersMuting the Sound Attenuating the Input SignalAdjusting the Tone Adjusting the Subwoofer Output LevelChanging the Source Name Basic SettingsAdjusting the Front Speaker Output Balance Recording a SourceSetting the Speakers for the DSP Modes Setting the Subwoofer InformationCrossover FRQ Crossover Frequency appears on the display To select the delay time of the rear speaker outputLFE ATT Low Frequency Effect Attenuator appears on Display Selecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingUsing the Sleep Timer Storing the Basic Settings AdjustmentsReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Selecting the FM Reception Mode Surround modes Using the DSP ModesWhat are the DSP Modes? DAP modes DVD Multi Playback ModeAvailable DSP modes according to the input mode Reproducing the Sound FieldBy pressing Surround on By pressing DSP MODE, Available DSP Modes According to the Speaker ArrangementAvailable DSP modes Adjusting the Surround Modes Level you want Press DSP Mode repeatedly untilAdjust the effect level Press Effect to select an effectDance CLUB, HALL, or Pavilion appears on Display Adjusting the DAP ModesDAP mode Live Club Adjust the rear speaker output levelsPress Surround ON/OFF To cancel the Dolby/DTS Surround modeTo cancel the DSP mode Activating the DSP ModesMulti appears on the display Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Press DVD Multi so that DVDAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingTerminals Video terminals AV Compu Link Remote Control SystemAV Compu Link terminal on the rear panel CASE1 If the components are equipped with the S-videoOne-Touch DVD Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlaySound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerREW CD changerTurntable Cassette deckPLAY3 Operating Video ComponentsDVD player Stops playing temporarily. To release it, pressOperating Other Manufacturers’ Video Equipment Press and hold TV PowerEnter manufacturer’s code using buttons Release TV PowerFor DBS tuner Release CATV/DBS PowerFor Catv converter If there are more than one code listed for your brand Release VCR PowerTry to operate your VCR by pressing VCR Power 04, 05 Release Audio PowerPlay JVC Denon Panasonic Philips PioneerProblem Possible Cause Solution TroubleshootingVideo SpecificationsAmplifier AudioGeneral Tuning Range Usable Sensitivity Signal-to-Noise RatioFM tuner IHF AM tunerValley Road Wayne, NJ QualityserviceFactory Service Center Locations 781 954 650Limited Warranty AUDIO-2 0101NHMMDWJEIN