Digital Input (DIGITAL IN) Terminal Setting
When you use the digital input terminals, you have to register what components are connected to which terminals (DIGITAL IN 1/2/3/4).
Before you start, remember....
•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the front panel ONLY:
To set the DIGITAL 1 terminal
1. Press SETTING repeatedly until | ST SETTING | |
“COAX DIG IN” appears on the |
|
|
|
| |
display. |
|
|
The display changes to show the current setting.
2. Press CONTROL UP 5/DOWN ° CONTROL
DOWN UP
to select the appropriate digital terminal setting.
•Each time you press the button, the display changes to show the following:
1 DVD Ò1 CDR Ò1 TV (or 1 DBS*) Ò1 CD Ò (back to the beginning)
*If you have changed the source name from “TV SOUND” to “DBS,” “DBS” appears (see page 13.)
When the DIGITAL 1 terminal is set, the DIGITAL 2/3/4 terminal is automatically set as follows:
DIGITAL 3 terminal setting
Selecting the Analog or Digital Input
Mode
When you have connected digital source components, you need to select the input mode correctly according to the connection you made.
Before you start, remember...
•The digital input (DIGITAL IN) terminal setting should be correctly done for the sources you want to select the digital input mode for. Without setting this digital input terminal correctly, you cannot change the input mode from analog input to digital input even if you follow the procedure below.
On the front panel:
1. Press one of the | DVD MULTI |
| DVD |
| VCR |
| TV SOUND/DBS |
|
|
| |||||
source selecting |
|
|
| ||||
|
|
|
|
|
| SOURCE NAME | |
|
|
|
|
|
| ||
buttons (DVD, TV |
|
|
|
|
|
| |
PHONO |
| CD |
| TAPE/CDR |
| FM/AM | |
|
|
| |||||
SOUND/DBS, CD, |
|
|
| ||||
|
|
|
|
|
|
| |
|
|
|
| SOURCE NAME |
|
| |
or TAPE/CDR)* |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
for which you |
|
|
|
|
|
|
|
want to change the input mode. |
|
|
|
| |||
Note:
*Among the sources listed above, you can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting.”)
2. Press INPUT ANALOG/ | INPUT |
DIGITAL to change the input | ANALOG/DIGITAL |
| |
mode. | INPUT ATT |
•Each time you press the button, the input mode changes as follows:
AUTO 
ANALOG
(Digital)
DIGITAL 2 terminal setting DIGITAL 4 terminal setting
When the DIGITAL 1 is set to “DVD”
2 CD 3 TV (or DBS*) 4 CDR
When the DIGITAL 1 is set to “CDR”
2 DVD 3 CD 4 TV (or DBS*)
When the DIGITAL 1 is set to “TV” or “DBS”
2 DVD 3 CD 4 CDR
AUTO: Select this for the digital input mode. The receiver automatically detects the incoming signal format. (The DIGITAL AUTO indicator lights up on the display, and the digital signal indicator for the detected signals also light up.)*
ANALOG: Select this for the analog input mode.
*The followings are the analog/digital signal indicators on the display to indicate what type of the signal comes into the receiver.
When the DIGITAL 1 is set to “CD”
2 DVD 3 TV (or DBS*) 4 CDR
*If you have changed the source name from “TV SOUND” to “DBS,” “DBS” appears (see page 13.)
Notes:
• When shipped from the factory, the DIGITAL IN terminals can be | ||
used as the digital input for the following components. | ||
• | DIGITAL 1 | (coaxial): For DVD player |
• | DIGITAL 2 | (optical): For CD player |
DIGITAL AUTO :
ANALOG :
LINEAR PCM :
DIGITAL:
:
Lights up when “AUTO” is selected as the digital input mode.
Lights up when the analog input is selected.
Lights up when Linear PCM signals come in.
Lights up when Dolby Digital signals come in.
Lights up when DTS Digital Surround signals come in.
• | DIGITAL 3 (optical): For digital TV broadcast tuner |
• | DIGITAL 4 (optical): For CDR |
• When using the DIGITAL 4 terminal for the CD recorder, you | |
need to select “CDR” as the source name. (See page 13.) | |
Continued to the next page.
16