JVC RX-7010VBK manual Getting Started, Before Installation, Connecting the FM and AM Antennas

Page 6

Getting Started

This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply.

Before Installation

General

Be sure your hands are dry.

Turn the power off to all components.

Read the manuals supplied with the components you are going to connect.

Locations

Install the receiver in a location that is level and protected from moisture.

The temperature around the receiver must be between –5˚ C and 35˚ C (23˚ F and 95˚ F).

Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

Handling the receiver

Do not insert any metal object into the receiver.

Do not disassemble the receiver or remove screws, covers, or cabinet.

Do not expose the receiver to rain or moisture.

Connecting the FM and AM Antennas

FM Antenna Connections

A

ANTENNA

75

B

ANTENNA

75

 

 

FM

 

 

FM

 

 

COAXIAL

 

 

COAXIAL

 

AM

AM

 

AM

AM

 

LOOP

EXT

 

LOOP

EXT

 

 

 

 

 

 

 

FM Antenna

 

 

ANTENNA

 

Extend the supplied FM antenna horizontally.

 

FM 75

 

 

 

 

COAXIAL

 

 

 

Checking the Supplied Accessories

Check to be sure you have all of the following items, which are supplied with the receiver.

The number in the parentheses indicates quantity of the pieces supplied.

Remote Control (1)

Batteries (2)

AM Loop Antenna (1)

FM Antenna (1)

If anything is missing, contact your dealer immediately.

AM

Outdoor FM Antenna Cable

LOOP

AM

EXT

A.Using the Supplied FM Antenna

The FM antenna provided can be connected to the FM 75 Ω COAXIAL terminal as temporary measure.

B.Using the Standard Type Connector (Not Supplied)

A standard type connector should be connected to the FM 75 Ω COAXIAL terminal.

Note:

If reception is poor, connect the outdoor antenna.

Before attaching a 75 Ω coaxial cable (the kind with a round wire going to an outdoor antenna), disconnect the supplied FM antenna.

3

Image 6
Contents RX-7010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents Parts Identification Remote ControlEx. When you press CD button Front PanelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure AM Antenna ConnectionsConnecting the rear and center speakers Connecting Audio/Video ComponentsConnecting the subwoofer speaker About the speaker impedanceVideo component connections CD playerTo audio output Cassette deck or CD recorderOutput TV and/or DBS tunerTo audio DBS tunerDigital connections Digital input terminalsDigital output terminal Plug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control R6PSUM-3/AA15FTurning the Power On and Off Standby Basic OperationsSelecting the Source to Play Selecting the Front Speakers Adjusting the VolumeListening only with headphones Selecting different sources for picture and soundAdjusting the Subwoofer Output Level Attenuating the Input SignalAdjusting the Tone Muting the SoundRecording a Source Basic SettingsAdjusting the Front Speaker Output Balance Changing the Source NameSetting the Subwoofer Information Setting the Speakers for the DSP ModesTo select the delay time of the rear speaker output LFE ATT Low Frequency Effect Attenuator appears on DisplayCrossover FRQ Crossover Frequency appears on the display Digital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeStoring the Basic Settings Adjustments Using the Sleep TimerTuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Selecting the FM Reception Mode Using the DSP Modes What are the DSP Modes?Surround modes Reproducing the Sound Field DVD Multi Playback ModeAvailable DSP modes according to the input mode DAP modesAvailable DSP Modes According to the Speaker Arrangement Available DSP modesBy pressing Surround on By pressing DSP MODE, Adjusting the Surround Modes Press Effect to select an effect Press DSP Mode repeatedly untilAdjust the effect level Level you wantAdjust the rear speaker output levels Adjusting the DAP ModesDAP mode Live Club Dance CLUB, HALL, or Pavilion appears on DisplayActivating the DSP Modes To cancel the Dolby/DTS Surround modeTo cancel the DSP mode Press Surround ON/OFFPress DVD Multi so that DVD Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Multi appears on the displaySynchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionCASE1 If the components are equipped with the S-video AV Compu Link Remote Control SystemAV Compu Link terminal on the rear panel Terminals Video terminalsOne-Touch Video Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch DVD PlayTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierCassette deck CD changerTurntable REWStops playing temporarily. To release it, press Operating Video ComponentsDVD player PLAY3Release TV Power Press and hold TV PowerEnter manufacturer’s code using buttons Operating Other Manufacturers’ Video EquipmentRelease CATV/DBS Power For Catv converterFor DBS tuner Release VCR Power Try to operate your VCR by pressing VCR PowerIf there are more than one code listed for your brand JVC Denon Panasonic Philips Pioneer Release Audio PowerPlay 04, 05Troubleshooting Problem Possible Cause SolutionAudio SpecificationsAmplifier VideoAM tuner Tuning Range Usable Sensitivity Signal-to-Noise RatioFM tuner IHF General781 954 650 QualityserviceFactory Service Center Locations Valley Road Wayne, NJLimited Warranty AUDIO-2 0101NHMMDWJEIN