JVC RX-7010VBK manual Muting the Sound, Attenuating the Input Signal, Reinforcing the Bass

Page 15

Muting the Sound

From the remote control ONLY:

Press MUTING to mute the sound

MUTING

 

through all speakers and headphones

 

connected.

“MUTING” appears on the display and the volume turns off (the volume level indicator goes off).

From the remote control:

Press BASS +/– or TREBLE +/– to adjust the bass or treble sound level (+10 dB to –10 dB).

Attenuating the Input Signal

BASS +

TREBLE+

To restore the sound, press MUTING again so that “OFF” appears on the display.

Turning MASTER VOLUME on the front panel or pressing VOLUME +/– on the remote control also restores the sound.

When the input level of the playing source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion.

Reinforcing the Bass

You can boost the bass level.

Press BASS BOOST on the front panel or on the remote control to select the bass boost function.

BASS BOOSTBASSBOOST

On the front panel ONLY:

Press and hold INPUT ATT so that the INPUT ATT indicator lights up on the display.

Each time you press and hold the button, the Input Attenuator mode turns on (“INPUT ATT ON”) or off (“INPUT NORMAL”).

Notes:

INPUT

ANALOG/DIGITAL

INPUT ATT

On the front panel

On the remote

 

control

Each time you press the button, the bass boost function turns on (“BASSBOOST ON”) and off (“BASSBOOST OFF”).

Select “BASSBOOST ON” to activate the bass boost function. The BASS BOOST indicator lights up on the display.

Select “BASSBOOST OFF” to cancel it.

The indicator goes off.

Note:

This function affects the front speaker sounds only.

Adjusting the Tone

You can adjust the bass and treble sounds as you like.

Before you start, remember....

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel:

 

1. Press ADJUST repeatedly until

ADJUST SETTING

“BASS” or “TREBLE” appears on

 

the display.

 

Select “BASS” to adjust the bass sound level.

Select “TREBLE” to adjust the treble sound level.

2. Press CONTROL UP 5/DOWN ° CONTROL

DOWN UP

to adjust the bass or treble sound level (+10 dB to –10 dB).

Each time you press the button, the sound level changes by ± 2 steps.

This function is available only for the sources connected using the analog terminals.

This function takes effect when the DSP mode is in use.

When selecting “DVD MULTI” as the source, this effect does not work.

Adjusting the Subwoofer Output Level

You can adjust the subwoofer output level if you have selected “YES” for the “SUBWOOFER” (see page 14).

Once it has been adjusted, the receiver memorizes the adjustment.

Before you start, remember....

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

When the front speakers are all deactivated, the subwoofer level cannot be adjusted.

On the front panel:

 

1. Press ADJUST repeatedly until

ADJUST SETTING

“SUBWFR LEVEL” appears on

 

the display.

 

The display changes to show the current setting.

2.

Press CONTROL UP 5/DOWN ° DOWN UP

 

 

CONTROL

 

to adjust the subwoofer output

 

 

level (+10 dB to –10 dB).

 

From the remote control:

 

1.

Press SOUND.

SOUND

 

 

The 10 keys are activated for sound adjustments.

2. Press SUBWOOFER +/– to adjust

–SUBWOOFER+

the subwoofer output level (+10 dB

0

+10

 

FMMODE

100+

to –10 dB).

12

Image 15
Contents RX-7010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents Front Panel Remote ControlEx. When you press CD button Parts IdentificationGetting Started Before InstallationConnecting the FM and AM Antennas Checking the Supplied AccessoriesAM Antenna Connections Connecting the SpeakersBasic connecting procedure Connecting the front speakersAbout the speaker impedance Connecting Audio/Video ComponentsConnecting the subwoofer speaker Connecting the rear and center speakersCassette deck or CD recorder CD playerTo audio output Video component connectionsDBS tuner TV and/or DBS tunerTo audio OutputDigital connections Digital input terminalsDigital output terminal R6PSUM-3/AA15F Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletTurning the Power On and Off Standby Basic OperationsSelecting the Source to Play Selecting different sources for picture and sound Adjusting the VolumeListening only with headphones Selecting the Front SpeakersMuting the Sound Attenuating the Input SignalAdjusting the Tone Adjusting the Subwoofer Output LevelChanging the Source Name Basic SettingsAdjusting the Front Speaker Output Balance Recording a SourceSetting the Speakers for the DSP Modes Setting the Subwoofer InformationTo select the delay time of the rear speaker output LFE ATT Low Frequency Effect Attenuator appears on DisplayCrossover FRQ Crossover Frequency appears on the display Selecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingUsing the Sleep Timer Storing the Basic Settings AdjustmentsTuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Selecting the FM Reception Mode Using the DSP Modes What are the DSP Modes?Surround modes DAP modes DVD Multi Playback ModeAvailable DSP modes according to the input mode Reproducing the Sound FieldAvailable DSP Modes According to the Speaker Arrangement Available DSP modesBy pressing Surround on By pressing DSP MODE, Adjusting the Surround Modes Level you want Press DSP Mode repeatedly untilAdjust the effect level Press Effect to select an effectDance CLUB, HALL, or Pavilion appears on Display Adjusting the DAP ModesDAP mode Live Club Adjust the rear speaker output levelsPress Surround ON/OFF To cancel the Dolby/DTS Surround modeTo cancel the DSP mode Activating the DSP ModesMulti appears on the display Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Press DVD Multi so that DVDAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingTerminals Video terminals AV Compu Link Remote Control SystemAV Compu Link terminal on the rear panel CASE1 If the components are equipped with the S-videoOne-Touch DVD Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlaySound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerREW CD changerTurntable Cassette deckPLAY3 Operating Video ComponentsDVD player Stops playing temporarily. To release it, pressOperating Other Manufacturers’ Video Equipment Press and hold TV PowerEnter manufacturer’s code using buttons Release TV PowerRelease CATV/DBS Power For Catv converterFor DBS tuner Release VCR Power Try to operate your VCR by pressing VCR PowerIf there are more than one code listed for your brand 04, 05 Release Audio PowerPlay JVC Denon Panasonic Philips PioneerProblem Possible Cause Solution TroubleshootingVideo SpecificationsAmplifier AudioGeneral Tuning Range Usable Sensitivity Signal-to-Noise RatioFM tuner IHF AM tunerValley Road Wayne, NJ QualityserviceFactory Service Center Locations 781 954 650Limited Warranty AUDIO-2 0101NHMMDWJEIN