JVC RX-7010VBK manual Release Audio Power, Play, JVC Denon Panasonic Philips Pioneer, 04, 05

Page 40

To change the transmittable signals for operating another manufacturer’s DVD player

1.Press and hold AUDIO POWER.

2.Press DVD.

3.Enter manufacturer’s code using buttons 1–9,

and 0.

See the list to the right to find the code.

4. Release AUDIO POWER.

After pressing DVD or DVD MULTI, you can perform the following operations on a DVD player:

PLAY3:

Starts playing.

4:

Returns to the beginning of the current (or

¢:

previous) tracks.

Skips to the beginning of the next track.

STOP7:

Stops playing.

PAUSE8:

Stops playing temporarily. To release it, press

 

PLAY.

Manufacturer

Codes

JVC

00, 02

DENON

01

PANASONIC

03

PHILIPS

13

PIONEER

04, 05, 06

RCA

07

SAMSUNG

08

SONY

09

TOSHIBA

10

YAMAHA

11, 12

Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.

After pressing DVD or DVD MULTI, these buttons can be used for the DVD menu operations.

Note:

For detailed menu operations, refer to the

instructions supplied with the discs or the DVD player.

– CENTER+

 

2

3

 

 

MENU

TEST

– REAR• L+

4

5

6

 

 

ENTER

– REAR• R+

8 9

Note:

Refer to the manual supplied with your DVD player.

5.Try to operate your DVD player by pressing one of the above buttons.

DO NOT forget to turn on the DVD player before pressing one of the above buttons.

If there are more than one code listed for your brand of DVD

player, try each one until the correct one is entered.

37

Image 40
Contents RX-7010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents Remote Control Ex. When you press CD buttonParts Identification Front PanelBefore Installation Connecting the FM and AM AntennasChecking the Supplied Accessories Getting StartedConnecting the Speakers Basic connecting procedureConnecting the front speakers AM Antenna ConnectionsConnecting Audio/Video Components Connecting the subwoofer speakerConnecting the rear and center speakers About the speaker impedanceCD player To audio outputVideo component connections Cassette deck or CD recorderTV and/or DBS tuner To audioOutput DBS tunerDigital input terminals Digital connectionsDigital output terminal Connecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet R6PSUM-3/AA15FBasic Operations Turning the Power On and Off StandbySelecting the Source to Play Adjusting the Volume Listening only with headphonesSelecting the Front Speakers Selecting different sources for picture and soundAttenuating the Input Signal Adjusting the ToneAdjusting the Subwoofer Output Level Muting the SoundBasic Settings Adjusting the Front Speaker Output BalanceRecording a Source Changing the Source NameSetting the Subwoofer Information Setting the Speakers for the DSP ModesLFE ATT Low Frequency Effect Attenuator appears on Display To select the delay time of the rear speaker outputCrossover FRQ Crossover Frequency appears on the display Digital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeStoring the Basic Settings Adjustments Using the Sleep TimerUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Selecting the FM Reception Mode What are the DSP Modes? Using the DSP ModesSurround modes DVD Multi Playback Mode Available DSP modes according to the input modeReproducing the Sound Field DAP modesAvailable DSP modes Available DSP Modes According to the Speaker ArrangementBy pressing Surround on By pressing DSP MODE, Adjusting the Surround Modes Press DSP Mode repeatedly until Adjust the effect levelPress Effect to select an effect Level you wantAdjusting the DAP Modes DAP mode Live ClubAdjust the rear speaker output levels Dance CLUB, HALL, or Pavilion appears on DisplayTo cancel the Dolby/DTS Surround mode To cancel the DSP modeActivating the DSP Modes Press Surround ON/OFFUsing the DVD Multi Playback Mode Activating the DVD Multi Playback ModePress DVD Multi so that DVD Multi appears on the displayCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverSynchronized Recording Automatic Source SelectionAV Compu Link Remote Control System AV Compu Link terminal on the rear panelCASE1 If the components are equipped with the S-video Terminals Video terminalsAutomatic Selection of TV’s Input Mode Automatic Power On/OffOne-Touch Video Play One-Touch DVD PlayOperating JVC’s Audio/Video Components Operating Audio ComponentsTuner Sound control section AmplifierCD changer TurntableCassette deck REWOperating Video Components DVD playerStops playing temporarily. To release it, press PLAY3Press and hold TV Power Enter manufacturer’s code using buttonsRelease TV Power Operating Other Manufacturers’ Video EquipmentFor Catv converter Release CATV/DBS PowerFor DBS tuner Try to operate your VCR by pressing VCR Power Release VCR PowerIf there are more than one code listed for your brand Release Audio Power PlayJVC Denon Panasonic Philips Pioneer 04, 05Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierAudio VideoTuning Range Usable Sensitivity Signal-to-Noise Ratio FM tuner IHFAM tuner GeneralQualityservice Factory Service Center Locations781 954 650 Valley Road Wayne, NJLimited Warranty AUDIO-2 0101NHMMDWJEIN