JVC RX-7010VBK manual Selecting the Front Speakers, Adjusting the Volume, On the front panel only

Page 14

Selecting different sources for picture and sound

You can watch picture from a video component while listening to sound from another component.

Press one of the audio source selecting buttons — PHONO, CD, TAPE/CDR, FM/AM, TV SOUND/DBS* (or TV/DBS on the remote control), while viewing the picture from a video component such as the VCR, DVD player, or DBS tuner, etc.

Notes:

• Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source.

*The TV SOUND/DBS (or TV/DBS on the remote control) only works for selecting “DBS” as the source but not for selecting “TV SOUND (or TV on the remote control).” When you use the DBS tuner, change the source name correctly (see page 13).

Selecting the Front Speakers

On the front panel ONLY:

When you have connected two pairs of the front speakers, you can select which to use.

SPEAKERS ON/OFF

1

2

To use the speakers connected to the FRONT SPEAKERS 1

terminals, press SPEAKERS ON/OFF 1 so that the SPK 1 indicator lights up on the display. (Make sure that the SPK 2 is not on the display.)

To use the speakers connected to the FRONT SPEAKERS 2

terminals, press SPEAKERS ON/OFF 2 so that the SPK 2 indicator lights up on the display. (Make sure that the SPK 1 is not on the display.)

Adjusting the Volume

On the front panel:

To increase the volume, turn MASTER

VOLUME clockwise.

To decrease the volume, turn it counterclockwise.

When you turn MASTER VOLUME rapidly, the volume level also changes rapidly.

When you turn MASTER VOLUME slowly, the volume level also changes slowly.

From the remote control:

To increase the volume, press VOLUME +. To decrease the volume, press VOLUME –.

MASTER VOLUME

+

VOLUME

To use both sets of the speakers, press SPEAKERS ON/OFF 1 and 2 so that the SPK 1 and SPK 2 indicators light up on the display.

To use neither sets of the speakers, press SPEAKERS ON/OFF 1 and 2 so that the SPK 1 and SPK 2 indicators disappear from the display.

Notes:

If you select any of the DSP modes while using both the speakers connected to the FRONT SPEAKERS 1 and 2 terminals, the speakers connected to the FRONT SPEAKERS 2 terminals are deactivated.

While the DSP MODE is in use, you can only select either the speakers connected to the FRONT SPEAKERS 1 or 2 terminals.

Listening only with headphones

You must turn off both pairs of speakers when you listen with headphones.

CAUTION:

Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.

Note:

The volume level can be adjusted within the range of “0” (minimum) to “80” (maximum).

1.Connect a pair of headphones to the PHONES jack on the front panel.

2.Press SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2 so that neither the SPK 1 nor SPK 2 indicator appears on the display.

This cancels the DSP mode currently selected, and activates the HEADPHONE mode (see below).

“HEADPHONE” appears and H. PHONE indicator lights up on the display.

HEADPHONE mode:

This mode can reproduce the LFE channel signals, mixing them with the front channel signals. So you will not miss the subwoofer sounds even if you listen to a source using the headphones.

Notes:

While in the HEADPHONE mode, you cannot use any DSP modes (see page 20.)

Activating the speaker cancels the HEADPHONE mode and turns on the DSP mode previously selected.

CAUTION:

Be sure to turn down the volume before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.

11

Image 14
Contents RX-7010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents Parts Identification Remote ControlEx. When you press CD button Front PanelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure AM Antenna ConnectionsConnecting the rear and center speakers Connecting Audio/Video ComponentsConnecting the subwoofer speaker About the speaker impedanceVideo component connections CD playerTo audio output Cassette deck or CD recorderOutput TV and/or DBS tunerTo audio DBS tunerDigital output terminal Digital connectionsDigital input terminals Plug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control R6PSUM-3/AA15FSelecting the Source to Play Turning the Power On and Off StandbyBasic Operations Selecting the Front Speakers Adjusting the VolumeListening only with headphones Selecting different sources for picture and soundAdjusting the Subwoofer Output Level Attenuating the Input SignalAdjusting the Tone Muting the SoundRecording a Source Basic SettingsAdjusting the Front Speaker Output Balance Changing the Source NameSetting the Subwoofer Information Setting the Speakers for the DSP ModesCrossover FRQ Crossover Frequency appears on the display To select the delay time of the rear speaker outputLFE ATT Low Frequency Effect Attenuator appears on Display Digital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeStoring the Basic Settings Adjustments Using the Sleep TimerReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Selecting the FM Reception Mode Surround modes Using the DSP ModesWhat are the DSP Modes? Reproducing the Sound Field DVD Multi Playback ModeAvailable DSP modes according to the input mode DAP modesBy pressing Surround on By pressing DSP MODE, Available DSP Modes According to the Speaker ArrangementAvailable DSP modes Adjusting the Surround Modes Press Effect to select an effect Press DSP Mode repeatedly untilAdjust the effect level Level you wantAdjust the rear speaker output levels Adjusting the DAP ModesDAP mode Live Club Dance CLUB, HALL, or Pavilion appears on DisplayActivating the DSP Modes To cancel the Dolby/DTS Surround modeTo cancel the DSP mode Press Surround ON/OFFPress DVD Multi so that DVD Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Multi appears on the displaySynchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionCASE1 If the components are equipped with the S-video AV Compu Link Remote Control SystemAV Compu Link terminal on the rear panel Terminals Video terminalsOne-Touch Video Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch DVD PlayTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierCassette deck CD changerTurntable REWStops playing temporarily. To release it, press Operating Video ComponentsDVD player PLAY3Release TV Power Press and hold TV PowerEnter manufacturer’s code using buttons Operating Other Manufacturers’ Video EquipmentFor DBS tuner Release CATV/DBS PowerFor Catv converter If there are more than one code listed for your brand Release VCR PowerTry to operate your VCR by pressing VCR Power JVC Denon Panasonic Philips Pioneer Release Audio PowerPlay 04, 05Troubleshooting Problem Possible Cause SolutionAudio SpecificationsAmplifier VideoAM tuner Tuning Range Usable Sensitivity Signal-to-Noise RatioFM tuner IHF General781 954 650 QualityserviceFactory Service Center Locations Valley Road Wayne, NJLimited Warranty AUDIO-2 0101NHMMDWJEIN