JVC RX-7010VBK manual Specifications, Amplifier, Audio, Video

Page 42

Specifications

Amplifier

Output Power

At Stereo operation:

Front channels:

100 W per channel, min. RMS, driven into 8 Ω, 40 Hz to 20 kHz with no more than 0.8% total harmonic distortion.

At Surround operation:

 

Front channels:

100 W per channel, min. RMS, driven into 8 Ω at 1 kHz with no

 

more than 0.8% total harmonic distortion.

Center channel:

100 W, min. RMS, driven into 8 Ω at 1 kHz, with no more than

 

0.8% total harmonic distortion.

Rear channels

100 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no

 

more than 0.8% total harmonic distortion.

Audio

 

 

2.7 mV/47 kΩ

Audio Input Sensitivity/Impedance (1 kHz):

PHONO (MM):

 

 

CD, TAPE/CDR, TV SOUND/DBS, VCR, DVD:

 

 

 

220 mV/47 kΩ

Audio Input (DIGITAL IN)* :

Coaxial: DIGITAL 1

(DVD):

0.5 V(p-p)/75 Ω

 

Optical: DIGITAL 2

(CD), DIGITAL 3 (TV), DIGITAL 4 (CDR):

–21 dBm to –15 dBm (660 nm ±30 nm)

*Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency — 32 kHz, 44.1 kHz, 48 kHz).

Audio Output Level:

TAPE/CDR, VCR:

220 mV

Digital output:

Optical: DIGITAL OUTPUT

 

Signal wave length: 660 nm

 

Output level: –21 dBm to –15 dBm

Signal-to-Noise Ratio (’66 IHF/’78 IHF):

PHONO (MM):

70 dB/78 dB (at REC OUT)

 

CD, TAPE/CDR, TV SOUND/DBS, VCR, DVD:

 

 

87 dB/67 dB

Frequency Response (8 Ω)

PHONO:

20 Hz to 20 kHz (±1 dB)

 

CD, TAPE/CDR, TV SOUND/DBS, VCR, DVD:

 

 

20 Hz to 20 kHz (±1 dB)

RIAA Phono Equalization:

±1.0 dB (20 Hz to 20 kHz)

Bass boost:

+3 dB ±1.0 dB at 100 Hz

Tone Control:

Bass (100 Hz):

±10 dB

 

Treble (10 kHz):

±10 dB

Video

Video Input Sensitivity/Impedance:

 

 

 

Composite video:

DBS, VCR, DVD:

 

1 V(p-p)/75 Ω

S-video:

DBS, VCR, DVD:

(Y: luminance):

1 V(p-p)/75 Ω

 

 

(C: chrominance, burst):

0.286 V(p-p)/75 Ω

Video Output Level:

 

 

1 V(p-p)/75 Ω

Composite video:

VCR, MONITOR OUT:

 

S-video:

VCR, MONITOR OUT:

(Y: luminance):

1 V(p-p)/75 Ω

 

 

(C: chrominance, burst): 0.286 V(p-p)/75 Ω

Synchronization:

Negative

 

 

Signal-to-Noise Ratio:

45 dB

 

 

39

Image 42
Contents RX-7010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents Parts Identification Remote ControlEx. When you press CD button Front PanelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure AM Antenna ConnectionsConnecting the rear and center speakers Connecting Audio/Video ComponentsConnecting the subwoofer speaker About the speaker impedanceVideo component connections CD playerTo audio output Cassette deck or CD recorderOutput TV and/or DBS tunerTo audio DBS tunerDigital connections Digital input terminalsDigital output terminal Plug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control R6PSUM-3/AA15FTurning the Power On and Off Standby Basic OperationsSelecting the Source to Play Selecting the Front Speakers Adjusting the VolumeListening only with headphones Selecting different sources for picture and soundAdjusting the Subwoofer Output Level Attenuating the Input SignalAdjusting the Tone Muting the SoundRecording a Source Basic SettingsAdjusting the Front Speaker Output Balance Changing the Source NameSetting the Subwoofer Information Setting the Speakers for the DSP ModesTo select the delay time of the rear speaker output LFE ATT Low Frequency Effect Attenuator appears on DisplayCrossover FRQ Crossover Frequency appears on the display Digital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeStoring the Basic Settings Adjustments Using the Sleep TimerTuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Selecting the FM Reception Mode Using the DSP Modes What are the DSP Modes?Surround modes Reproducing the Sound Field DVD Multi Playback ModeAvailable DSP modes according to the input mode DAP modesAvailable DSP Modes According to the Speaker Arrangement Available DSP modesBy pressing Surround on By pressing DSP MODE, Adjusting the Surround Modes Press Effect to select an effect Press DSP Mode repeatedly untilAdjust the effect level Level you wantAdjust the rear speaker output levels Adjusting the DAP ModesDAP mode Live Club Dance CLUB, HALL, or Pavilion appears on DisplayActivating the DSP Modes To cancel the Dolby/DTS Surround modeTo cancel the DSP mode Press Surround ON/OFFPress DVD Multi so that DVD Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Multi appears on the displaySynchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionCASE1 If the components are equipped with the S-video AV Compu Link Remote Control SystemAV Compu Link terminal on the rear panel Terminals Video terminalsOne-Touch Video Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch DVD PlayTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierCassette deck CD changerTurntable REWStops playing temporarily. To release it, press Operating Video ComponentsDVD player PLAY3Release TV Power Press and hold TV PowerEnter manufacturer’s code using buttons Operating Other Manufacturers’ Video EquipmentRelease CATV/DBS Power For Catv converterFor DBS tuner Release VCR Power Try to operate your VCR by pressing VCR PowerIf there are more than one code listed for your brand JVC Denon Panasonic Philips Pioneer Release Audio PowerPlay 04, 05Troubleshooting Problem Possible Cause SolutionAudio SpecificationsAmplifier VideoAM tuner Tuning Range Usable Sensitivity Signal-to-Noise RatioFM tuner IHF General781 954 650 QualityserviceFactory Service Center Locations Valley Road Wayne, NJLimited Warranty AUDIO-2 0101NHMMDWJEIN