JVC RX-7010VBK manual Release VCR Power, Try to operate your VCR by pressing VCR Power

Page 39

To change the transmittable signals for operating another manufacturer’s VCR

1.Press and hold VCR POWER.

2.Press VCR.

3.Enter manufacturer’s code using buttons 1–9,

and 0.

See the list to the right to find the code.

4. Release VCR POWER.

The following button can be used for operating the VCR:

VCR POWER: Turns on and off the VCR.

After pressing VCR, you can perform the following operations on the VCR:

CH +/–:

Changes the TV channels on the VCR.

1 – 10, 0, 100+ (+10): Selects the TV channels.

 

The 10 button will function as the

 

ENTER button if your VCR requires

 

pressing ENTER after selecting a

PLAY3:

channel number.

Starts playback.

REW:

Rewinds a video tape.

FF:

Fast winds a video tape.

STOP7:

Stops operation.

PAUSE8:

Pauses.

REC PAUSE:

Starts recording or enters recording pause.

Note:

Refer to the manual supplied with your VCR.

5. Try to operate your VCR by pressing VCR POWER.

When your VCR turns on or off, you have entered the correct code.

If there are more than one code listed for your brand of

VCR, try each one until the correct one is entered.

Manufacturer

Codes

JVC

00, 26, 27, 28, 29, 58

AIWA

01, 02

BELL & HOWELL

03

BLAUPUNKT

04, 05

CGM

06, 07

EMERSON

08, 10, 11, 12, 64, 65

FISHER

03, 14, 15, 16, 17

FUNAI

01

GE

18, 19, 20

GOLDSTAR

07

GOODMANS

13, 21

GRUNDIG

06, 22

HITACHI

18, 23, 24, 25, 66

LOEWE

07, 21

MAGNAVOX

04, 19, 24

MITSUBISHI

30, 31, 32, 33, 34, 35

NEC

26, 27

NOKIA

03, 36

NORDMENDE

38

ORION

09

PANASONIC

19, 24, 39, 40

PHILIPS

04, 19, 21, 24, 41, 42

PHONOLA

21

RCA/PROSCAN

04, 18, 19, 23, 24, 43, 44,

 

45

SABA

38, 46

SAMSUNG

45, 47, 59, 61, 62, 63

SANYO

03, 48, 49

SHARP

37, 50

SIEMENS

03, 51

SONY

52, 53, 54

TELEFUNKEN

55, 60

TOSHIBA

43, 44

ZENITH

57

Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.

36

Image 39
Contents RX-7010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents Front Panel Remote ControlEx. When you press CD button Parts IdentificationGetting Started Before InstallationConnecting the FM and AM Antennas Checking the Supplied AccessoriesAM Antenna Connections Connecting the SpeakersBasic connecting procedure Connecting the front speakersAbout the speaker impedance Connecting Audio/Video ComponentsConnecting the subwoofer speaker Connecting the rear and center speakersCassette deck or CD recorder CD playerTo audio output Video component connectionsDBS tuner TV and/or DBS tunerTo audio OutputDigital connections Digital input terminalsDigital output terminal R6PSUM-3/AA15F Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletTurning the Power On and Off Standby Basic OperationsSelecting the Source to Play Selecting different sources for picture and sound Adjusting the VolumeListening only with headphones Selecting the Front SpeakersMuting the Sound Attenuating the Input SignalAdjusting the Tone Adjusting the Subwoofer Output LevelChanging the Source Name Basic SettingsAdjusting the Front Speaker Output Balance Recording a SourceSetting the Speakers for the DSP Modes Setting the Subwoofer InformationTo select the delay time of the rear speaker output LFE ATT Low Frequency Effect Attenuator appears on DisplayCrossover FRQ Crossover Frequency appears on the display Selecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingUsing the Sleep Timer Storing the Basic Settings AdjustmentsTuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Selecting the FM Reception Mode Using the DSP Modes What are the DSP Modes?Surround modes DAP modes DVD Multi Playback ModeAvailable DSP modes according to the input mode Reproducing the Sound FieldAvailable DSP Modes According to the Speaker Arrangement Available DSP modesBy pressing Surround on By pressing DSP MODE, Adjusting the Surround Modes Level you want Press DSP Mode repeatedly untilAdjust the effect level Press Effect to select an effectDance CLUB, HALL, or Pavilion appears on Display Adjusting the DAP ModesDAP mode Live Club Adjust the rear speaker output levelsPress Surround ON/OFF To cancel the Dolby/DTS Surround modeTo cancel the DSP mode Activating the DSP ModesMulti appears on the display Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Press DVD Multi so that DVDAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingTerminals Video terminals AV Compu Link Remote Control SystemAV Compu Link terminal on the rear panel CASE1 If the components are equipped with the S-videoOne-Touch DVD Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlaySound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerREW CD changerTurntable Cassette deckPLAY3 Operating Video ComponentsDVD player Stops playing temporarily. To release it, pressOperating Other Manufacturers’ Video Equipment Press and hold TV PowerEnter manufacturer’s code using buttons Release TV PowerRelease CATV/DBS Power For Catv converterFor DBS tuner Release VCR Power Try to operate your VCR by pressing VCR PowerIf there are more than one code listed for your brand 04, 05 Release Audio PowerPlay JVC Denon Panasonic Philips PioneerProblem Possible Cause Solution TroubleshootingVideo SpecificationsAmplifier AudioGeneral Tuning Range Usable Sensitivity Signal-to-Noise RatioFM tuner IHF AM tunerValley Road Wayne, NJ QualityserviceFactory Service Center Locations 781 954 650Limited Warranty AUDIO-2 0101NHMMDWJEIN