JVC RX-7010VBK Connecting the Power Cord, Putting Batteries in the Remote Control, R6PSUM-3/AA15F

Page 12

Connecting the Power Cord

Before plugging the receiver into an AC outlet, make sure that all connections have been made.

Plug the power cord into an AC outlet.

Putting Batteries in the Remote Control

Before using the remote control, put two supplied batteries first. When using the remote control, aim the remote control directly at the remote sensor on the receiver.

Keep the power cord away from the connecting cables and the antenna. The power cord may cause noise or screen interference. We recommend that you use a coaxial cable to connect the antenna, since it is well-shielded against interference.

Note:

The preset settings such as preset channels and sound adjustment may be erased in a few days in the following cases:

When you unplug the power cord.

When a power failure occurs.

CAUTIONS:

Do not touch the power cord with wet hands.

Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

1

2

R6P(SUM-3)/AA(15F)

3

1.On the back of the remote control, remove the battery cover.

2.Insert batteries. Make sure to match the polarity:

(+) to (+) and (–) to (–).

3.Replace the cover.

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

Place batteries in the remote control so they match the polarity:

(+) to (+) and (–) to (–).

Use the correct type of batteries. Batteries that look similar may differ in voltage.

Always replace both batteries at the same time.

Do not expose batteries to heat or flame.

9

Image 12
Contents RX-7010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents Remote Control Ex. When you press CD buttonParts Identification Front PanelBefore Installation Connecting the FM and AM AntennasChecking the Supplied Accessories Getting StartedConnecting the Speakers Basic connecting procedureConnecting the front speakers AM Antenna ConnectionsConnecting Audio/Video Components Connecting the subwoofer speakerConnecting the rear and center speakers About the speaker impedanceCD player To audio outputVideo component connections Cassette deck or CD recorderTV and/or DBS tuner To audioOutput DBS tunerDigital connections Digital input terminalsDigital output terminal Connecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet R6PSUM-3/AA15FTurning the Power On and Off Standby Basic OperationsSelecting the Source to Play Adjusting the Volume Listening only with headphonesSelecting the Front Speakers Selecting different sources for picture and soundAttenuating the Input Signal Adjusting the ToneAdjusting the Subwoofer Output Level Muting the SoundBasic Settings Adjusting the Front Speaker Output BalanceRecording a Source Changing the Source NameSetting the Subwoofer Information Setting the Speakers for the DSP ModesTo select the delay time of the rear speaker output LFE ATT Low Frequency Effect Attenuator appears on DisplayCrossover FRQ Crossover Frequency appears on the display Digital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeStoring the Basic Settings Adjustments Using the Sleep TimerTuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Selecting the FM Reception Mode Using the DSP Modes What are the DSP Modes?Surround modes DVD Multi Playback Mode Available DSP modes according to the input modeReproducing the Sound Field DAP modesAvailable DSP Modes According to the Speaker Arrangement Available DSP modesBy pressing Surround on By pressing DSP MODE, Adjusting the Surround Modes Press DSP Mode repeatedly until Adjust the effect levelPress Effect to select an effect Level you wantAdjusting the DAP Modes DAP mode Live ClubAdjust the rear speaker output levels Dance CLUB, HALL, or Pavilion appears on DisplayTo cancel the Dolby/DTS Surround mode To cancel the DSP modeActivating the DSP Modes Press Surround ON/OFFUsing the DVD Multi Playback Mode Activating the DVD Multi Playback ModePress DVD Multi so that DVD Multi appears on the displayCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverSynchronized Recording Automatic Source SelectionAV Compu Link Remote Control System AV Compu Link terminal on the rear panelCASE1 If the components are equipped with the S-video Terminals Video terminalsAutomatic Selection of TV’s Input Mode Automatic Power On/OffOne-Touch Video Play One-Touch DVD PlayOperating JVC’s Audio/Video Components Operating Audio ComponentsTuner Sound control section AmplifierCD changer TurntableCassette deck REWOperating Video Components DVD playerStops playing temporarily. To release it, press PLAY3Press and hold TV Power Enter manufacturer’s code using buttonsRelease TV Power Operating Other Manufacturers’ Video EquipmentRelease CATV/DBS Power For Catv converterFor DBS tuner Release VCR Power Try to operate your VCR by pressing VCR PowerIf there are more than one code listed for your brand Release Audio Power PlayJVC Denon Panasonic Philips Pioneer 04, 05Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierAudio VideoTuning Range Usable Sensitivity Signal-to-Noise Ratio FM tuner IHFAM tuner GeneralQualityservice Factory Service Center Locations781 954 650 Valley Road Wayne, NJLimited Warranty AUDIO-2 0101NHMMDWJEIN