Weider WEBE37330 user manual Is shown pulled away from the Center Upright for clarity

Page 18

39.Locate the Long Cable (68). Route the eyelet end of the Cable through the Foot Plate (67) and the Center Upright (45), and under a Pulley (87).

Attach the Pulley (87) inside the Center Upright

(45)with an M10 x 75mm Bolt (92), two M10 Washers (35), two 17mm Spacers (89), and an M10 Nylon Locknut (34). Note: The Foot Plate

(67)is shown pulled away from the Center Upright for clarity.

40.Wrap the Long Cable (68) over a Pulley (87). Attach the Pulley to the Double “U”-bracket (81) with an M10 x 45mm Bolt (33) and an M10 Nylon Locknut (34).

41.Wrap the Long Cable (68) under a Pulley (87). Attach the Pulley to the Weight Guide Base (41) with an M10 x 45mm Bolt (33) and an M10 Nylon Locknut (34).

42.Wrap the Long Cable (68) over a Pulley (87). Attach the Pulley and a Cable Trap (88) to the second set of holes from the bottom of the Pulley Plates (82) with an M10 x 45mm Bolt (33) and an M10 Nylon Locknut (34). Make sure the Cable

Trap is oriented to hold the Cable in the groove of the Pulley.

43.Attach the Long Cable (68) inside the Weight Guide Base (41) with an M10 x 75mm Bolt (92), two M10 Washers (35), two 28mm Spacers (91), and an M10 Nylon Locknut (34).

44.Make sure that all parts are properly tightened before the weight bench is used. The use of all remaining parts will be explained in ADJUST- MENTS, beginning on the following page.

39
45
	87
34	35
	89
68	89 35
67	92
67
40
34	81
	81
	33
	87
	68
41
68
87
34
	41
	33
42
	82
	33
34	87
	87
	88
	68
43
34
68
35
91
	41
	91
	35
	92

18

Image 18

Contents QUESTIONS? Model No. WEBE37330 Serial NoCustomer HOT Line Table of Contents Decal Important Precautions Before YOU Begin Right SideLeft Side Assembly Make Things Easier for YourselfDo not tighten the Locknuts yet Other Small Base Cap in the same manner Locknuts 34. Do not tighten the Locknuts yetTighten the M10 Nylon Locknuts 34 used Steps Page Assemble the other Pad Tube 27 in the same manner Locknuts yet Repeat this step with the Right Base not shownHoles 110 Tighten the Locknuts yet Locknuts yet Tighten the M10 Nylon Locknuts 34 used Steps Right Safety Spotter not shown in the same Manner Locate the Medium Cable 69. Route the Cable Locate the Butterfly Cable 109. Attach Cable Trap is oriented to hold the CableGroove of the Pulley Is shown pulled away from the Center Upright for clarity Seat 10 can be adjusted in the same man- ner AdjustmentsAdjusting the Backrest and Seat Attaching the Curl PAD or LEG LeverAttaching the Accessories Adding Weight to the LEG LeverAdding Weight to the Weight Carriage Using the AB SlingsAttaching the DIP ARM Using the Weight Rests and Safety SpottersSetting UP for Squat Exercises Knobs 22 are fully tightenedMoving the Bench Tightening the CablesButterfly Cable Cable DiagramsMedium Cable Long CableExercise Guidelines Muscle Chart Cooling DownStaying Motivated Aerobic Exercise Exercise Weight Sets RepsDate Thursday Aerobic Exercise DateMonday Part Identification CHART-Model No. WEBE37330 R0803BPage 48mm Weight Carriage Cap Part LIST-Model No. WEBE37330 Qty DescriptionExploded DRAWING-Model No. WEBE37330 Exploded Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT