Weider WESY97300 Locate the Press Cable, Two 5/16 Nylon Jam Nuts, Cable to pivot, Locknut

Page 13

CABLE ASSEMBLY

23.Attach the High Cable (23) to a Small “U”- Bracket (67) with a 1/4” Nylon Locknut (2)

and a 1/4” Washer (10). Do not completely

tighten the Nylon Locknut. It should be threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing.

24. Locate the Press Cable (58).	Attach the
Press Cable to the Rear Upright (56) with a
5/16” x 3” Bolt (93), a 5/16” Washer (8), and
two 5/16” Nylon Jam Nuts (84).	The end of
the Cable must be between the two Nylon
Jam Nuts and there must be enough room
between the Nylon Jam Nuts for the end
of the Cable to pivot.

Wrap the Press Cable (58) around a 3 1/2” Pulley (15). Attach the Pulley and a Cable Trap (66) to the Squat Arm (79) with a 3/8” x

3 3/4” Bolt (71), a 3/8” Washer (9), and a 3/8”

Nylon	Locknut (21).	The Cable Trap must be
turned	to hold the Cable in place.

25. Attach the end of the Press Cable (58) to the Long “U”-Bracket (57) with a 1/4” Nylon Lock-

nut (2) and a 1/4” Washer (10). Do not com- pletely tighten the Nylon Locknut. It

should be threaded onto the end of the Cable so only a couple of threads are showing above the nut, as shown in the inset drawing.

13

23
		23
	23	67
	10	67
	10
	2	10
	67	2
24
		21
	79	9
	58	93
66	15	8
		8
		56
		56
71	84
25
		58
		57
		10
	58
	10	2
	2
	57

Image 13

Contents Patent Pending QUESTIONS?Model No. WESY97300 Serial No Serial Number DecalLimited Warranty Table of ContentsIng down Important PrecautionsBefore YOU Begin Using the Weider PRO 9730 Home Gym SystemFrame Assembly AssemblyFollowing Tools not Included are Required for Assembly Before beginning assembly, be sure thatDo not tighten Nylon Locknuts yet This side Lubricate Pins Slide eight Weights 25 onto the WeightSame side Must be atThat the indicated holes are on the side Shown Frame Assembly ARM AssemblyTap two 1 Retainers 69 and a 1 Round 2 Bolt 7 and a 3/8 Nylon LocknutAttach the Left Arm 47 in the same manner Welded Brackets Lubricate AxleLocate the High Cable Be sure that Cable AssemblyPulley Bracket must Route the High Cable 23 around one Assembly8 Nylon Locknut Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon LocknutTwo 5/16 Nylon Jam Nuts Locate the Press CableCable to pivot LocknutSlide the Low Cable into place under the 3 1/2 Low Pulley Locate the Low CablePress Frame 17 and that the Cable is Press FramePulley as shown Be sure that Cable Trap is turned to hold the CableWrap the Low Cable 86 around a V-Pulley Locate the Rear Cable 95. Attach the Rear Onto the Bolt. Do not overtighten the Nylon LocknutCable must be routed from the direc- tion shown 4 Bolt 87 and a 3/8 Nylon LocknutSeat Plate to a Seat 13 with two 1/4 x 3/4 Screws Two 1/4 WashersUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Upright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Seat AssemblyThick End Tighten a 1/4 Nylon Locknut 2 with aWith the Bolt and a 5/16 Nylon Locknut Press a 1 1/2 Square Inner Cap 32 into the Leg LeverLubricate-33 Pin Misc Changing the Weight Setting AdjustmentAttaching the LAT BAR or Nylon Strap to High Pulley Station Cable with two Cable ClipsAttach one end of the Chain 52 to the Low Cable Attaching the LEG Lever to the LOW Pulley StationAttaching and Removing the Seats With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat KnobLbs Weight Resistance ChartFrom the Weight Tube not shown or remove TROUBLE-SHOOTING and MaintenanceTightening the Cables Woven cable, the type of cable used on the homeWeight Stack Cable DiagramsRear Base Press Cable Rear Upright High CableOrdering Replacement Parts WESY97300 R1097A Check to see if it has been pre-assembled16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Description Part LIST-Model No. WESY97300Exploded