Weider WESY97300 user manual Round Inner Cap

Page 32

3/4" Round Inner Cap (34)–

1" Round Inner Cap (49)–6

1" Round Cover Cap (70)–6

5/16" x 2" Eyebolt (35)—1

1" Square Inner Cap (65)—1

2" Square Cover Cap (78)–2

1 3/4" Square Inner Cap (44)–7

1 1/2" Square Inner Cap (32)—2

2" Square Inner Cap (27)–6

1" x 2" Inner Cap (83)–2

Image 32

Contents QUESTIONS? Patent PendingModel No. WESY97300 Serial No Serial Number DecalTable of Contents Limited WarrantyImportant Precautions Ing downUsing the Weider PRO 9730 Home Gym System Before YOU BeginAssembly Frame AssemblyFollowing Tools not Included are Required for Assembly Before beginning assembly, be sure thatDo not tighten Nylon Locknuts yet Slide eight Weights 25 onto the Weight This side Lubricate PinsSame side Must be atFrame Assembly ARM Assembly That the indicated holes are on the side Shown2 Bolt 7 and a 3/8 Nylon Locknut Tap two 1 Retainers 69 and a 1 RoundAttach the Left Arm 47 in the same manner Welded Brackets Lubricate AxleLocate the High Cable Pulley Bracket must Cable AssemblyBe sure that Assembly Route the High Cable 23 around one8 Nylon Locknut Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon LocknutLocate the Press Cable Two 5/16 Nylon Jam NutsCable to pivot LocknutLocate the Low Cable Slide the Low Cable into place under the 3 1/2 Low PulleyPress Frame 17 and that the Cable is Press FrameWrap the Low Cable 86 around a V-Pulley Be sure that Cable Trap is turned to hold the CablePulley as shown Onto the Bolt. Do not overtighten the Nylon Locknut Locate the Rear Cable 95. Attach the Rear4 Bolt 87 and a 3/8 Nylon Locknut Cable must be routed from the direc- tion shownUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Two 1/4 WashersSeat Plate to a Seat 13 with two 1/4 x 3/4 Screws Seat Assembly Upright 42 with two 1/4 x 2 1/2 Screws Two 1/4 WashersThick End Tighten a 1/4 Nylon Locknut 2 with aLubricate-33 Pin Press a 1 1/2 Square Inner Cap 32 into the Leg LeverWith the Bolt and a 5/16 Nylon Locknut Misc Adjustment Changing the Weight SettingAttaching the LAT BAR or Nylon Strap to High Pulley Station Cable with two Cable ClipsAttaching the LEG Lever to the LOW Pulley Station Attach one end of the Chain 52 to the Low CableAttaching and Removing the Seats With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat KnobWeight Resistance Chart LbsTROUBLE-SHOOTING and Maintenance From the Weight Tube not shown or removeTightening the Cables Woven cable, the type of cable used on the homeRear Base Cable DiagramsWeight Stack High Cable Press Cable Rear UprightOrdering Replacement Parts Check to see if it has been pre-assembled WESY97300 R1097A16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Part LIST-Model No. WESY97300 DescriptionExploded