Weider WESY97300 user manual Bolt 7 and a 3/8 Nylon Locknut, Tap two 1 Retainers 69 and a 1 Round

Page 9

ARM ASSEMBLY

10.Press a 1 3/4” Square Inner Cap (44) into the top of a Press Arm (46). Press a 1” Round

Inner Cap (49) into the side of the Press Arm. Attach the Press Arm to one side of the

Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3).

Assemble the other Press Arm (46) in the same manner.

11.Identify the Right Arm (48) and the Left Arm (47). Note the position of the welded bracket

on each Arm. Arm identification is very important for step 12.

Attach a “V”-Pulley (6) and a Long Cable Trap (50) to the Right Arm (48) with a 3/8” x

2 .1/2” Bolt (7) and a 3/8” Nylon Locknut (21).

Attach a “V”-Pulley (6) and a Long Cable Trap (50) to the Left Arm (47) with a 3/8” x

2 .1/2” Bolt (7) and a 3/8” Nylon Locknut (21).

12.Lubricate both axles on the Top Frame (55).

Slide the Right Arm (48) onto the right axle.

Note: Be careful not to confuse the Right

Arm with the Left Arm (47); refer to step 11 to identify the Right Arm. Be sure that the upper end of the Right Arm is behind the indicated bracket on the Top Frame (55).

Tap two 1” Retainers (69) and a 1” Round

Cover Cap (70) onto the right axle. Be sure that the teeth on the Retainers bend

toward the Cover Cap, as shown in the inset drawing.

Attach the Left Arm (47) in the same manner.

Press 1 3/4” Square Inner Caps (44) into the lower ends of the Right and Left Arms (47, 48). Wet the lower end of each Arm with

soapy water. Slide a 10” Pad (45) onto the lower end of each Arm.

9

10

 

44

49

 

 

 

44

 

 

 

 

 

 

46

49

 

 

 

46

22

 

 

 

 

 

 

 

17

3

 

 

 

11

7

50

 

 

 

50

6

 

 

 

 

47

Welded

 

 

 

 

 

Brackets

 

 

 

 

 

21

 

48

 

 

 

12

 

 

 

 

 

Bracket

47

 

 

 

55

 

Lubricate

 

 

Axle

 

 

 

69

45

 

 

70

 

48

 

 

 

44

 

 

 

 

 

Axle

 

45

 

 

69

 

 

 

70

Image 9
Contents Patent Pending QUESTIONS?Model No. WESY97300 Serial No Serial Number DecalLimited Warranty Table of ContentsIng down Important PrecautionsBefore YOU Begin Using the Weider PRO 9730 Home Gym SystemFrame Assembly AssemblyFollowing Tools not Included are Required for Assembly Before beginning assembly, be sure thatDo not tighten Nylon Locknuts yet This side Lubricate Pins Slide eight Weights 25 onto the WeightSame side Must be atThat the indicated holes are on the side Shown Frame Assembly ARM AssemblyTap two 1 Retainers 69 and a 1 Round 2 Bolt 7 and a 3/8 Nylon LocknutAttach the Left Arm 47 in the same manner Welded Brackets Lubricate AxleLocate the High Cable Cable Assembly Be sure thatPulley Bracket must Route the High Cable 23 around one Assembly8 Nylon Locknut Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon LocknutTwo 5/16 Nylon Jam Nuts Locate the Press CableCable to pivot LocknutSlide the Low Cable into place under the 3 1/2 Low Pulley Locate the Low CablePress Frame 17 and that the Cable is Press FrameBe sure that Cable Trap is turned to hold the Cable Pulley as shownWrap the Low Cable 86 around a V-Pulley Locate the Rear Cable 95. Attach the Rear Onto the Bolt. Do not overtighten the Nylon LocknutCable must be routed from the direc- tion shown 4 Bolt 87 and a 3/8 Nylon LocknutTwo 1/4 Washers Seat Plate to a Seat 13 with two 1/4 x 3/4 ScrewsUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Upright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Seat AssemblyThick End Tighten a 1/4 Nylon Locknut 2 with aPress a 1 1/2 Square Inner Cap 32 into the Leg Lever With the Bolt and a 5/16 Nylon LocknutLubricate-33 Pin Misc Changing the Weight Setting AdjustmentAttaching the LAT BAR or Nylon Strap to High Pulley Station Cable with two Cable ClipsAttach one end of the Chain 52 to the Low Cable Attaching the LEG Lever to the LOW Pulley StationAttaching and Removing the Seats With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat KnobLbs Weight Resistance ChartFrom the Weight Tube not shown or remove TROUBLE-SHOOTING and MaintenanceTightening the Cables Woven cable, the type of cable used on the homeCable Diagrams Weight StackRear Base Press Cable Rear Upright High CableOrdering Replacement Parts WESY97300 R1097A Check to see if it has been pre-assembled16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Description Part LIST-Model No. WESY97300Exploded