Weider WESY97300 user manual Slide eight Weights 25 onto the Weight, Same side, Must be at, Top

Page 7

FRAME ASSEMBLY

5.Set two Weight Bumpers (19) onto one of the brackets on the Stabilizer (5). Insert two Weight Guides (62) through the Weight Bumpers and the bracket on the Stabilizer.

Be sure that the drilled holes in the Weight Guides are at the top, as shown. Press a 1” Round Cover Cap (70) onto the bottom of each Weight Guide.

Slide eight Weights (25) onto the Weight

Guides (62). Be sure that all of the Weights are turned so the pin grooves are on the

same side.

Assemble the other stack of Weights (25) in the same manner.

6.Press a Weight Tube Bumper (64) into the end of a Weight Tube (63). Insert the Weight Tube into either stack of Weights (25). Be sure that the pins on the Weight Tube are resting in the pin grooves in the upper Weight.

Lubricate the insides of the holes in a Top Weight (76). Slide the Top Weight onto the Weight Guides (62) and set it on the stack of Weights (25).

Assemble the other Weight Tube (63) and Top Weight (76) in the same manner.

7

5			Drilled holes
			Drilled holes
			must be at
			the top
			62
			Pin Grooves
			must be on
62			this side
62
			25
Pin Grooves
must be on
this side			19
		70	5
			5
			70
25
6
			62
			Lubricate
			76
	63		Pins
	63
			64
			25
63
76
	25

Image 7

Contents Serial Number Decal QUESTIONS?Patent Pending Model No. WESY97300 Serial NoLimited Warranty Table of ContentsIng down Important PrecautionsBefore YOU Begin Using the Weider PRO 9730 Home Gym SystemBefore beginning assembly, be sure that AssemblyFrame Assembly Following Tools not Included are Required for AssemblyDo not tighten Nylon Locknuts yet Must be at Slide eight Weights 25 onto the WeightThis side Lubricate Pins Same sideThat the indicated holes are on the side Shown Frame Assembly ARM AssemblyWelded Brackets Lubricate Axle 2 Bolt 7 and a 3/8 Nylon LocknutTap two 1 Retainers 69 and a 1 Round Attach the Left Arm 47 in the same mannerLocate the High Cable Be sure that Cable AssemblyPulley Bracket must Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon Locknut AssemblyRoute the High Cable 23 around one 8 Nylon LocknutLocknut Locate the Press CableTwo 5/16 Nylon Jam Nuts Cable to pivotPress Frame Locate the Low CableSlide the Low Cable into place under the 3 1/2 Low Pulley Press Frame 17 and that the Cable isPulley as shown Be sure that Cable Trap is turned to hold the CableWrap the Low Cable 86 around a V-Pulley Locate the Rear Cable 95. Attach the Rear Onto the Bolt. Do not overtighten the Nylon LocknutCable must be routed from the direc- tion shown 4 Bolt 87 and a 3/8 Nylon LocknutSeat Plate to a Seat 13 with two 1/4 x 3/4 Screws Two 1/4 WashersUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Tighten a 1/4 Nylon Locknut 2 with a Seat AssemblyUpright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Thick EndWith the Bolt and a 5/16 Nylon Locknut Press a 1 1/2 Square Inner Cap 32 into the Leg LeverLubricate-33 Pin Misc Cable with two Cable Clips AdjustmentChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to High Pulley StationWith the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat Knob Attaching the LEG Lever to the LOW Pulley StationAttach one end of the Chain 52 to the Low Cable Attaching and Removing the SeatsLbs Weight Resistance ChartWoven cable, the type of cable used on the home TROUBLE-SHOOTING and MaintenanceFrom the Weight Tube not shown or remove Tightening the CablesWeight Stack Cable DiagramsRear Base Press Cable Rear Upright High CableOrdering Replacement Parts WESY97300 R1097A Check to see if it has been pre-assembled16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Description Part LIST-Model No. WESY97300Exploded