Weider WESY97300 user manual Locate the High Cable

Page 10

13.Press two 1” x 2” Inner Caps (83) into the indicated end of the Squat Arm (79).

Lubricate a 3/8” x 3 1/4” Bolt (85). Attach the Squat Arm (79) to the Front Upright (42) with the Bolt and a 3/8” Nylon Locknut (21).

Attach a Handle (92) to one side of the Squat

Arm (79) with a 5/16” x 2 1/2” Bolt (22), two 5/16” W ashers (8), a 1/2” x 17/32” Spacer (94), and a 5/16” Nylon Locknut (3).

Attach the other Handle (92) to the other side of the Squat Arm (79) in the same manner.

ARM ASSEMBLY

14.During steps 15 through 39, refer to the CABLE DIAGRAMS on pages 26 and 27 of this manual to verify proper cable routing.

Before beginning this section, identify the High Cable (23), the Low Cable (86), the Rear Cable (95), and the Press Cable (58) by comparing the lengths and ends of the

cables.

IMPORTANT: While assembling the cables, do not overtighten the bolts and nuts securing the pulleys. The pulleys must be able to turn freely.

ASSEMBLY	15.	Pulley to the Top Frame (55) with a 3/8” x
		Locate the High Cable (23).	Wrap the High
		Cable around a 3 1/2” Pulley (15). Attach the
CABLE		3 .3/4” Bolt (71) and a 3/8” Nylon Locknut
		the ball is on the indicated side of the
		(21). Be sure that the end of the Cable with

Pulley and that the Cable is between the

Pulley and the hook.

10

13
		8	22
		8	92
22		83
22		94
83		94
83	8	8
92	8	8
92		3
94	8	79	21
94
	3
	3
			42
			85
			Lubricate
14
			86 (148”)
			23 (159”)
			58 (47”)
			95 (141”)
15			23
		55	23
		55
21
	Ball	15
	Ball
	Hook		71
	Hook

Image 10

Contents Model No. WESY97300 Serial No QUESTIONS?Patent Pending Serial Number DecalTable of Contents Limited WarrantyImportant Precautions Ing downUsing the Weider PRO 9730 Home Gym System Before YOU BeginFollowing Tools not Included are Required for Assembly AssemblyFrame Assembly Before beginning assembly, be sure thatDo not tighten Nylon Locknuts yet Same side Slide eight Weights 25 onto the WeightThis side Lubricate Pins Must be atFrame Assembly ARM Assembly That the indicated holes are on the side ShownAttach the Left Arm 47 in the same manner 2 Bolt 7 and a 3/8 Nylon LocknutTap two 1 Retainers 69 and a 1 Round Welded Brackets Lubricate AxleLocate the High Cable Be sure that Cable AssemblyPulley Bracket must 8 Nylon Locknut AssemblyRoute the High Cable 23 around one Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon LocknutCable to pivot Locate the Press CableTwo 5/16 Nylon Jam Nuts LocknutPress Frame 17 and that the Cable is Locate the Low CableSlide the Low Cable into place under the 3 1/2 Low Pulley Press FramePulley as shown Be sure that Cable Trap is turned to hold the CableWrap the Low Cable 86 around a V-Pulley Onto the Bolt. Do not overtighten the Nylon Locknut Locate the Rear Cable 95. Attach the Rear4 Bolt 87 and a 3/8 Nylon Locknut Cable must be routed from the direc- tion shownSeat Plate to a Seat 13 with two 1/4 x 3/4 Screws Two 1/4 WashersUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Thick End Seat AssemblyUpright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Tighten a 1/4 Nylon Locknut 2 with aWith the Bolt and a 5/16 Nylon Locknut Press a 1 1/2 Square Inner Cap 32 into the Leg LeverLubricate-33 Pin Misc Attaching the LAT BAR or Nylon Strap to High Pulley Station AdjustmentChanging the Weight Setting Cable with two Cable ClipsAttaching and Removing the Seats Attaching the LEG Lever to the LOW Pulley StationAttach one end of the Chain 52 to the Low Cable With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat KnobWeight Resistance Chart LbsTightening the Cables TROUBLE-SHOOTING and MaintenanceFrom the Weight Tube not shown or remove Woven cable, the type of cable used on the homeWeight Stack Cable DiagramsRear Base High Cable Press Cable Rear UprightOrdering Replacement Parts Check to see if it has been pre-assembled WESY97300 R1097A16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Part LIST-Model No. WESY97300 DescriptionExploded