Weider WESY97300 Frame Assembly ARM Assembly, That the indicated holes are on the side Shown

Page 8

FRAME ASSEMBLY

ARM ASSEMBLY

7. Press a 2” Square Inner Cap (27) into each

7

 

 

 

end of the Top Frame (55). Press a 1 3/4”

 

 

 

 

 

 

 

Square Inner Cap (44) into each end of the

 

 

 

 

crossbar on the Top Frame. Press two 1”

 

 

 

 

Round Inner Caps (49) into the top of the

 

 

 

 

crossbar.

 

 

 

 

 

Attach the Top Frame (55) to the Front Upright

 

11

11

 

 

 

 

 

 

 

 

(42) and the Rear Upright (56) with four 5/16”

 

 

 

 

x 2 3/4” Bolts (11), four 5/16” Washers (8),

 

 

 

27

and four 5/16” Nylon Locknuts (3).

27

8

8

44

 

 

 

 

49

 

 

 

 

 

27

 

 

55

 

 

 

 

 

27

 

 

Crossbar

 

 

 

44

 

 

 

 

3

 

 

 

 

 

 

 

3

 

 

 

 

56

 

 

 

 

 

 

 

42

8. Attach the each set of the Weight Guides (62)

8

 

 

 

to the Top Frame (55) with a 5/16” x 6” Bolt

 

 

 

 

 

 

61

(60), two 1/2” x 3/4” Spacers (61), and a 5/16”

 

 

3

 

 

 

Nylon Locknut (3).

 

61

 

 

 

62

 

 

 

 

 

 

 

55

 

Tighten all Nylon Locknuts used in steps 3

 

 

60

through 8.

 

 

 

 

 

 

 

3

 

 

 

 

 

 

60

 

 

 

 

 

62

 

 

9. Press a 1” x 7/8” Plastic Bushing (75) onto

9

 

 

 

each welded spacer on the Press Frame (17).

 

Holes must be

 

 

Slide the Press Frame into place on the Front

 

 

 

 

 

on this side

Base (4).

Note: This will be a tight fit. The

 

 

 

 

Plastic Bushings should fit onto each end

 

 

 

Lubricate

of the indicated tube in the Base. Be sure

 

17

 

that the indicated holes are on the side

 

 

59

 

 

 

shown.

 

 

 

 

 

Lubricate the 3/8” x 8” Bolt (59). Attach the

 

 

 

Welded

 

 

 

Spacers

Press Frame (17) to the Front Base (4) with

 

21

 

 

 

 

the Bolt and a 3/8” Nylon Locknut (21).

 

 

 

 

 

75

 

 

 

4

 

 

Tube

 

 

 

 

 

 

 

 

 

8

 

 

 

Image 8
Contents QUESTIONS? Patent PendingModel No. WESY97300 Serial No Serial Number DecalTable of Contents Limited WarrantyImportant Precautions Ing downUsing the Weider PRO 9730 Home Gym System Before YOU BeginAssembly Frame AssemblyFollowing Tools not Included are Required for Assembly Before beginning assembly, be sure thatDo not tighten Nylon Locknuts yet Slide eight Weights 25 onto the Weight This side Lubricate PinsSame side Must be atFrame Assembly ARM Assembly That the indicated holes are on the side Shown2 Bolt 7 and a 3/8 Nylon Locknut Tap two 1 Retainers 69 and a 1 RoundAttach the Left Arm 47 in the same manner Welded Brackets Lubricate AxleLocate the High Cable Pulley Bracket must Cable AssemblyBe sure that Assembly Route the High Cable 23 around one8 Nylon Locknut Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon LocknutLocate the Press Cable Two 5/16 Nylon Jam NutsCable to pivot LocknutLocate the Low Cable Slide the Low Cable into place under the 3 1/2 Low PulleyPress Frame 17 and that the Cable is Press FrameWrap the Low Cable 86 around a V-Pulley Be sure that Cable Trap is turned to hold the CablePulley as shown Onto the Bolt. Do not overtighten the Nylon Locknut Locate the Rear Cable 95. Attach the Rear4 Bolt 87 and a 3/8 Nylon Locknut Cable must be routed from the direc- tion shownUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Two 1/4 WashersSeat Plate to a Seat 13 with two 1/4 x 3/4 Screws Seat Assembly Upright 42 with two 1/4 x 2 1/2 Screws Two 1/4 WashersThick End Tighten a 1/4 Nylon Locknut 2 with aLubricate-33 Pin Press a 1 1/2 Square Inner Cap 32 into the Leg LeverWith the Bolt and a 5/16 Nylon Locknut Misc Adjustment Changing the Weight SettingAttaching the LAT BAR or Nylon Strap to High Pulley Station Cable with two Cable ClipsAttaching the LEG Lever to the LOW Pulley Station Attach one end of the Chain 52 to the Low CableAttaching and Removing the Seats With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat KnobWeight Resistance Chart LbsTROUBLE-SHOOTING and Maintenance From the Weight Tube not shown or removeTightening the Cables Woven cable, the type of cable used on the homeRear Base Cable DiagramsWeight Stack High Cable Press Cable Rear UprightOrdering Replacement Parts Check to see if it has been pre-assembled WESY97300 R1097A16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Part LIST-Model No. WESY97300 DescriptionExploded