Weider WESY97300 Seat Assembly, Upright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers, Thick End

Page 19

SEAT ASSEMBLY

43. Attach the Large Backrest (41) to the Front

 

43

 

 

Upright (42) with two 1/4” x 2 1/2” Screws

 

 

 

 

 

(43) and two 1/4” Washers (10).

The

 

 

 

Backrest must be oriented as shown.

 

 

 

 

 

 

 

 

41

 

 

43

10

42

 

 

 

 

 

 

 

 

Thick End

44. Press a 1 1/2” Square Inner Cap (32) into the

44

 

 

Front Seat Frame (36).

 

 

 

 

 

 

 

Insert the 1/4” x 2 1/4” Carriage Bolt (38) into

 

 

 

the center hole in a Seat Plate (37). Attach

 

 

 

 

the Seat Plate to the Seat (13) with two 1/4” x

 

 

 

3/4” Screws (18).

 

 

 

 

Insert the 1/4” x 2 1/4” Carriage Bolt (38) into

 

 

13

the indicated hole in the Front Seat Frame

 

 

 

 

(36). Tighten a 1/4” Nylon Locknut (2) with a

 

 

 

1/4” Washer (10) onto the Carriage Bolt.

 

 

 

 

Attach the other end of the Seat (13) to the

 

 

 

38

Front Seat Frame (36) with a 1/4” Washer

 

 

37

 

(10) and the 1/4” x 2 1/4” Screw (82).

 

32

 

 

 

 

 

 

18

 

 

 

10

36

 

 

 

 

 

 

 

82

2

 

 

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Serial Number Decal QUESTIONS?Patent Pending Model No. WESY97300 Serial NoLimited Warranty Table of ContentsIng down Important PrecautionsBefore YOU Begin Using the Weider PRO 9730 Home Gym SystemBefore beginning assembly, be sure that AssemblyFrame Assembly Following Tools not Included are Required for AssemblyDo not tighten Nylon Locknuts yet Must be at Slide eight Weights 25 onto the WeightThis side Lubricate Pins Same sideThat the indicated holes are on the side Shown Frame Assembly ARM AssemblyWelded Brackets Lubricate Axle 2 Bolt 7 and a 3/8 Nylon LocknutTap two 1 Retainers 69 and a 1 Round Attach the Left Arm 47 in the same mannerLocate the High Cable Be sure that Cable AssemblyPulley Bracket must Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon Locknut AssemblyRoute the High Cable 23 around one 8 Nylon LocknutLocknut Locate the Press CableTwo 5/16 Nylon Jam Nuts Cable to pivotPress Frame Locate the Low CableSlide the Low Cable into place under the 3 1/2 Low Pulley Press Frame 17 and that the Cable isPulley as shown Be sure that Cable Trap is turned to hold the CableWrap the Low Cable 86 around a V-Pulley Locate the Rear Cable 95. Attach the Rear Onto the Bolt. Do not overtighten the Nylon LocknutCable must be routed from the direc- tion shown 4 Bolt 87 and a 3/8 Nylon LocknutSeat Plate to a Seat 13 with two 1/4 x 3/4 Screws Two 1/4 WashersUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Tighten a 1/4 Nylon Locknut 2 with a Seat AssemblyUpright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Thick EndWith the Bolt and a 5/16 Nylon Locknut Press a 1 1/2 Square Inner Cap 32 into the Leg LeverLubricate-33 Pin Misc Cable with two Cable Clips AdjustmentChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to High Pulley StationWith the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat Knob Attaching the LEG Lever to the LOW Pulley StationAttach one end of the Chain 52 to the Low Cable Attaching and Removing the SeatsLbs Weight Resistance ChartWoven cable, the type of cable used on the home TROUBLE-SHOOTING and MaintenanceFrom the Weight Tube not shown or remove Tightening the CablesWeight Stack Cable DiagramsRear Base Press Cable Rear Upright High CableOrdering Replacement Parts WESY97300 R1097A Check to see if it has been pre-assembled16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Description Part LIST-Model No. WESY97300Exploded
Top Page Image Contents