Weider WESY97300 user manual Cable Diagrams, Weight Stack, Rear Base

Page 26

CABLE DIAGRAMS

The cable diagrams on this page and the next page show the proper routing of the High Cable (23), the Low

Cable (86), the Rear Cable (95), and the Press Cable (58). Use the diagrams to be sure that the Cables have been assembled correctly. The starting and ending points of each Cable have been labeled. The numbers show

the proper route for each Cable.IMPORTANT: If the Cables have not been correctly routed, the WEIDER

PRO 9730 will not function properly and damage may occur.

Rear Cable (95)

Low Cable (86)

4

2

5

Weight Stack

3

1

Rear Base

26

7

 

 

4

 

3

6

5

 

1

8

Low Pulley

 

Front Base

2

Image 26
Contents Model No. WESY97300 Serial No QUESTIONS?Patent Pending Serial Number DecalTable of Contents Limited WarrantyImportant Precautions Ing downUsing the Weider PRO 9730 Home Gym System Before YOU BeginFollowing Tools not Included are Required for Assembly AssemblyFrame Assembly Before beginning assembly, be sure thatDo not tighten Nylon Locknuts yet Same side Slide eight Weights 25 onto the WeightThis side Lubricate Pins Must be atFrame Assembly ARM Assembly That the indicated holes are on the side ShownAttach the Left Arm 47 in the same manner 2 Bolt 7 and a 3/8 Nylon LocknutTap two 1 Retainers 69 and a 1 Round Welded Brackets Lubricate AxleLocate the High Cable Pulley Bracket must Cable AssemblyBe sure that 8 Nylon Locknut AssemblyRoute the High Cable 23 around one Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon LocknutCable to pivot Locate the Press CableTwo 5/16 Nylon Jam Nuts LocknutPress Frame 17 and that the Cable is Locate the Low CableSlide the Low Cable into place under the 3 1/2 Low Pulley Press FrameWrap the Low Cable 86 around a V-Pulley Be sure that Cable Trap is turned to hold the CablePulley as shown Onto the Bolt. Do not overtighten the Nylon Locknut Locate the Rear Cable 95. Attach the Rear4 Bolt 87 and a 3/8 Nylon Locknut Cable must be routed from the direc- tion shownUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Two 1/4 WashersSeat Plate to a Seat 13 with two 1/4 x 3/4 Screws Thick End Seat AssemblyUpright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Tighten a 1/4 Nylon Locknut 2 with aLubricate-33 Pin Press a 1 1/2 Square Inner Cap 32 into the Leg LeverWith the Bolt and a 5/16 Nylon Locknut Misc Attaching the LAT BAR or Nylon Strap to High Pulley Station AdjustmentChanging the Weight Setting Cable with two Cable ClipsAttaching and Removing the Seats Attaching the LEG Lever to the LOW Pulley StationAttach one end of the Chain 52 to the Low Cable With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat KnobWeight Resistance Chart LbsTightening the Cables TROUBLE-SHOOTING and MaintenanceFrom the Weight Tube not shown or remove Woven cable, the type of cable used on the homeRear Base Cable DiagramsWeight Stack High Cable Press Cable Rear UprightOrdering Replacement Parts Check to see if it has been pre-assembled WESY97300 R1097A16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Part LIST-Model No. WESY97300 DescriptionExploded