Weider WESY97300 Frame Assembly, Following Tools not Included are Required for Assembly

Page 5

ASSEMBLY

Before beginning assembly, carefully read the following information and instructions:

•Place all parts of the home gym system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed.

•The assembly is divided into four stages: 1) frame assembly, 2) press, squat, and butterfly arm assembly, 3) cable and pulley assembly, and

4)seat and backrest assembly. The hardware for each stage is packaged separately.

•Wait until you begin each assembly stage to open that parts bag.

•For help identifying the small parts used in assembly, use the PART IDENTIFICATION

CHART located in the center of this manual. Note: Some small parts may have been pre- attached for shipping. If a part is not in the parts bag, check to see if it has been pre-attached.

•As you assemble the home gym system, be sure that all parts are oriented as shown in the drawings.

•Tighten all parts as you assemble them, unless instructed to do otherwise.

THE FOLLOWING TOOLS (NOT INCLUDED) ARE

REQUIRED FOR ASSEMBLY:

• Two (2) adjustable wrenches

• One (1) standard screwdriver

• One (1) phillips screwdriver

• One (1) rubber mallet

•Lubricant, such as grease or petroleum jelly, and soapy water will also be needed.

Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.

FRAME ASSEMBLY

1. Before beginning assembly, be sure that

1

 

 

you have read and understand the infor-

 

 

 

 

 

mation in the box above.

27

51

 

Press a 2” Square Inner Cap (27) into the

 

11

78

 

 

 

end of the Rear Base (51). Press a 2” Square

 

 

 

Cover Cap (78) onto each end of the

 

 

 

Stabilizer (5).

 

 

 

Insert two 5/16” x 2 1/2” Carriage Bolts (1)

11

1

5

 

 

up through the Rear Base (51). Insert two

 

 

 

5/16” x 2 3/4” Bolts (11) through the Rear

78

 

 

Base and Stabilizer (5) as shown.

 

 

 

 

 

2. Press a 2” Square Inner Cap (27) into the

2

 

 

end of the Front Base (4).

 

 

 

 

 

Insert two 5/16” x 2 1/2” Carriage Bolts (1)

51

 

 

 

3

 

up through the Front Base (4). Slide the

5

 

Front Base onto the two 5/16” x 2 3/4” Bolts

 

 

 

 

 

(11) in the Rear Base (51) and Stabilizer (5).

 

 

4

Fully tighten two 5/16” Nylon Locknuts (3)

 

11

onto the Carriage Bolts.

 

 

 

 

 

 

 

1

 

 

 

 

27

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Patent Pending QUESTIONS?Model No. WESY97300 Serial No Serial Number DecalLimited Warranty Table of ContentsIng down Important PrecautionsBefore YOU Begin Using the Weider PRO 9730 Home Gym SystemFrame Assembly AssemblyFollowing Tools not Included are Required for Assembly Before beginning assembly, be sure thatDo not tighten Nylon Locknuts yet This side Lubricate Pins Slide eight Weights 25 onto the WeightSame side Must be atThat the indicated holes are on the side Shown Frame Assembly ARM AssemblyTap two 1 Retainers 69 and a 1 Round 2 Bolt 7 and a 3/8 Nylon LocknutAttach the Left Arm 47 in the same manner Welded Brackets Lubricate AxleLocate the High Cable Pulley Bracket must Cable AssemblyBe sure that Route the High Cable 23 around one Assembly8 Nylon Locknut Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon LocknutTwo 5/16 Nylon Jam Nuts Locate the Press CableCable to pivot LocknutSlide the Low Cable into place under the 3 1/2 Low Pulley Locate the Low CablePress Frame 17 and that the Cable is Press FrameWrap the Low Cable 86 around a V-Pulley Be sure that Cable Trap is turned to hold the CablePulley as shown Locate the Rear Cable 95. Attach the Rear Onto the Bolt. Do not overtighten the Nylon LocknutCable must be routed from the direc- tion shown 4 Bolt 87 and a 3/8 Nylon LocknutUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Two 1/4 WashersSeat Plate to a Seat 13 with two 1/4 x 3/4 Screws Upright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Seat AssemblyThick End Tighten a 1/4 Nylon Locknut 2 with aLubricate-33 Pin Press a 1 1/2 Square Inner Cap 32 into the Leg LeverWith the Bolt and a 5/16 Nylon Locknut Misc Changing the Weight Setting AdjustmentAttaching the LAT BAR or Nylon Strap to High Pulley Station Cable with two Cable ClipsAttach one end of the Chain 52 to the Low Cable Attaching the LEG Lever to the LOW Pulley StationAttaching and Removing the Seats With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat KnobLbs Weight Resistance ChartFrom the Weight Tube not shown or remove TROUBLE-SHOOTING and MaintenanceTightening the Cables Woven cable, the type of cable used on the homeRear Base Cable DiagramsWeight Stack Press Cable Rear Upright High CableOrdering Replacement Parts WESY97300 R1097A Check to see if it has been pre-assembled16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Description Part LIST-Model No. WESY97300Exploded
Top Page Image Contents