Weider WESY97300 user manual Attaching the LEG Lever to the LOW Pulley Station

Page 23

ATTACHING THE LEG LEVER TO THE LOW

PULLEY STATION

To use the Leg Lever (29), the seat must be attached to the front upright (see ATTACHING AND REMOV- ING THE SEATS below).

Attach one end of the Chain (52) to the Low Cable

(86)with a Cable Clip (53). Attach the other end of the Chain to the Eyebolt (35) with a Cable Clip.

Always remove the Chain (52) from the Eyebolt

(35)before removing the seat.

ATTACHING AND REMOVING THE SEATS

See drawing A. Set the bracket on the Front Seat Frame (36) onto the indicated pins on the Front Upright (42). Attach the Front Seat Frame to the Front

Upright with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40).

For some exercises, the Front Seat Frame (36) must be removed. First, be sure that the chain is not attached to the leg lever. Next, remove the Seat Knob

(40)and the 5/16” x 2 3/4” Carriage Bolt (14) from the Front Seat Frame. Lift the Front Seat Frame off the

Front Upright (42).

See drawing B. Align the holes in the Rear Seat

Frame (77) with one set of holes in the Rear Upright (56). Attach the Rear Seat Frame to the Rear Upright

with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40).

For some exercises, the Rear Seat Frame (77) must be removed. Remove the Seat Knob (40) and the

5/16” x 2 3/4” Carriage Bolt (14) from the Rear Seat Frame. Lift the Seat Frame off the Rear Upright (56).

 

 

 

53

 

 

 

52

 

 

35

29

 

 

 

86

 

 

 

A

 

 

 

42

 

40

 

36

 

 

 

14

 

 

 

B

 

 

 

 

 

 

40

 

 

77

 

 

14

 

56

 

 

 

23

Image 23
Contents Serial Number Decal QUESTIONS?Patent Pending Model No. WESY97300 Serial NoLimited Warranty Table of ContentsIng down Important PrecautionsBefore YOU Begin Using the Weider PRO 9730 Home Gym SystemBefore beginning assembly, be sure that AssemblyFrame Assembly Following Tools not Included are Required for AssemblyDo not tighten Nylon Locknuts yet Must be at Slide eight Weights 25 onto the WeightThis side Lubricate Pins Same sideThat the indicated holes are on the side Shown Frame Assembly ARM AssemblyWelded Brackets Lubricate Axle 2 Bolt 7 and a 3/8 Nylon LocknutTap two 1 Retainers 69 and a 1 Round Attach the Left Arm 47 in the same mannerLocate the High Cable Pulley Bracket must Cable AssemblyBe sure that Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon Locknut AssemblyRoute the High Cable 23 around one 8 Nylon LocknutLocknut Locate the Press CableTwo 5/16 Nylon Jam Nuts Cable to pivotPress Frame Locate the Low CableSlide the Low Cable into place under the 3 1/2 Low Pulley Press Frame 17 and that the Cable isWrap the Low Cable 86 around a V-Pulley Be sure that Cable Trap is turned to hold the CablePulley as shown Locate the Rear Cable 95. Attach the Rear Onto the Bolt. Do not overtighten the Nylon LocknutCable must be routed from the direc- tion shown 4 Bolt 87 and a 3/8 Nylon LocknutUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Two 1/4 WashersSeat Plate to a Seat 13 with two 1/4 x 3/4 Screws Tighten a 1/4 Nylon Locknut 2 with a Seat AssemblyUpright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Thick EndLubricate-33 Pin Press a 1 1/2 Square Inner Cap 32 into the Leg LeverWith the Bolt and a 5/16 Nylon Locknut Misc Cable with two Cable Clips AdjustmentChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to High Pulley StationWith the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat Knob Attaching the LEG Lever to the LOW Pulley StationAttach one end of the Chain 52 to the Low Cable Attaching and Removing the SeatsLbs Weight Resistance ChartWoven cable, the type of cable used on the home TROUBLE-SHOOTING and MaintenanceFrom the Weight Tube not shown or remove Tightening the CablesRear Base Cable DiagramsWeight Stack Press Cable Rear Upright High CableOrdering Replacement Parts WESY97300 R1097A Check to see if it has been pre-assembled16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Description Part LIST-Model No. WESY97300Exploded