Weider WESY74090 Short Cable 58 is between the Pulley 15, Cable Trap is oriented as shown

Page 10

Cable/Seat Assembly

12.Locate the parts bag labeled “CABLE ASSEMBLY AND PULLEYS.” For cable identification and rout-

ing during steps 12 through 27, refer to the Cable Diagram and Cable ID Chart on pages 15 and 16.

Slide a 3/8” Flat Washer (9) and a 1/2” x 1/4” Spacer

(44)onto a 3/8” x 2” Bolt (12). Next, hold a 3 1/2” Pulley (15) inside the slot in the Top Frame (55), and insert the Bolt through the Top Frame and the Pulley.

Slide another 1/2” x 1/4” Spacer (44) and another 3/8” Flat Washer (9) onto the Bolt and tighten a 3/8” Nylon Jamnut (22) onto the Bolt.

Locate the Short Cable (58). It is about 130” long and it has a ball on one end and a loop on the other end. Wrap the end with the ball around the

3 1/2” Pulley (15) in the direction shown.

Attach a 5/16” x 2” Bolt (78), a 1/2” x 1 3/8” Spacer (61), and a 5/16” Nylon Locknut (3) to the Top Frame

(55) in the indicated location. Make sure that the

Short Cable (58) is between the Pulley (15) and

the Spacer. Next, press a 1 1/2” Square Inner Cap

(32)into the indicated end of the Top Frame.

13.Remove the pre-attached Pulley (15) from the Large Pulley bracket (40).

Route the Short Cable (58) through the Large Pulley

Bracket (40) as shown.

Attach a 3 1/2” Pulley (15) inside the Large Pulley

Bracket (40) with a 3/8” x 1 3/4” Bolt (68) and a 3/8”

Nylon Jamnut (22).	Make sure the Cable runs over
the top of the Pulley.
Route the Short Cable (58) down through the hole in
the Top Frame (55).
14. Remove the pre-attached Pulleys (15) from the “I”-
Plates (20).
Wrap the Short Cable (58) around a 3 1/2” Pulley (15)
in the direction shown. Attach the Pulley and a Cable
Trap (66) to the top hole in the “I”-Plates with a 3/8” x
2” Bolt (12) and a 3/8” Nylon Locknut (21).		Note:
Make sure the “I”-Plates are oriented so the end
with two holes is pointed upward. Make sure the
Cable Trap is oriented as shown.

10

	12
		44
		15
	44	12
		58
	9
	22
		9
		78
		32
	55	3
	55
		61
	13	68
		68
	40
	Hole	15
		55
	22
	58
	14
	58	Two
	66	Two
	66	Holes
		21
	15
	12
	20

Image 10

Contents Model No. WESY74090 Serial No Serial Number DecalTable of Contents Limited WarrantyMake sure the cables remain on the pulleys Important PrecautionsPrecautions before using the weight system Keep hands and feet away from moving partsUsing the Weider Weight System Before You BeginAssembly To make the assembly process as smooth as possiBolts with two 5/16 Nylon Locknuts Locate and open the parts bag labeled Frame AssemblySee the inset drawing Tighten the Nylon Locknuts yetTighten all Nylon Locknuts used in steps 1 through SupportMake sure the welded tab on the Press Frame Locknut 3 do not tighten at this timeLocate and open the parts bag labeled ARM Is oriented as shownArm Right Axle with a hammerShort Cable 58 is between the Pulley 15 Cable Trap is oriented as shown8 x 1 Bolt 59, a 3/8 Plain Nut 56 and a 3/8 Spacer15b From Pulley To Pulley Onto the Bolt to prevent the Pulley from falling off durIng the following steps. Note Make sure the Pulley BracketMake sure the Cable Trap is oriented as shown Bolt 12 and a 3/8 Nylon Locknut 21. NoteSpacer To the Seat 13 with two 1/4 x 3/4 Screws Cable Diagram Shooting and Maintenance onLong Cable 76, 87 1/2Cise will be reduced AdjustmentPin Woven cable, the type of cable used on the home gym Trouble-shooting and MaintenanceMake sure the Cable Trap is oriented as shown Re-install it Additional slack can be removed by moving the upperLbs Weight Resistance ChartCables, pulleys, and weight guides 101 120 121 138 103Ordering Replacement Parts Part No J00885-C R0700ARemove this Part Identification Chart from the Manual WESY74090 R0700APart Identification Chart-WESY74090 Page Page Remove this Part LIST/EXPLODED Drawing from the Manual X 3/4 Screw Qty Description Key No. Qty16 x 2 1/4 Bolt Upright X 1/4 SpacerExploded Drawing-Model No. WESY74090