Weider WESY74090 user manual Spacer, 8 x 1 Bolt 59, a 3/8 Plain Nut 56 and a 3/8, 15b

Page 11

15.Refer to drawing 15a. Remove the 5/16” x 6” Bolt (7), the two 1/2” x 1” Spacers (51), the 1/2” x 1 3/8” Spacer (61), and the 5/16” Nylon Locknut (3) from the Weight Guides (62) and the Top Frame (55).

Refer to drawing 15b. Route the Short Cable (58) up through the indicated slot in the Top Frame (55). Wrap the Short Cable around a 3 1/2” Pulley (15) in the direction shown and slide the Pulley into the slot in the Top Frame from the back. Attach the Pulley inside

the slot with a 3/8” x 2” Bolt (12), two 1/2” x 1/4” Spacers (44), two 3/8” Flat Washers (9), and a 3/8” Nylon Jamnut (22).

Refer to drawing 15a. Re-attach the 5/16” x 6” Bolt

(7), the two 1/2” x 1” Spacers (51), the 1/2” x 1 3/8”

Spacer (61), and the 5/16” Nylon Locknut (3). Make sure that the Short Cable is between the Pulley

and the Spacer.

Refer to drawing 15b. Press a 1 1/2” Square Inner

Cap (32) into the indicated end of the Top Frame (55).

16. Attach the loop at the end of the Short Cable (58) to

the Weight Tube (63) with a 5/16” x 1 1/2” Bolt (11) and a 5/16” Nylon Locknut (3).

17.Locate the Butterfly Cable (76). It is approximately 87 1/2“ long and it has a closed loop on both ends.

Attach one end of the Butterfly Cable (76) to the welded bracket on the back of the Right Arm (48) with

a 3/8” x 1” Bolt (59), a 3/8” Plain Nut (56) and a 3/8”

Nylon Jamnut (22). Note: Make sure the Plain Nut and the Jamnut are mounted in the order shown here. Do not overtighten the Nylon Locknut; it must be possible to pivot the Cable.

18.Wrap the Butterfly Cable (76) around a Large Pulley

(39)in the direction shown.

Attach the Large Pulley (39) and a Long Cable Trap

(50) to the welded bracket on the right side of the

Upright (42) with a 3/8” x 2 1/2” Bolt (60) and a 3/8”

Nylon Locknut (21). Note: Make sure the Cable Trap is oriented as shown.

15a

 

15b

 

44

 

61

 

 

 

 

15

 

 

3

 

 

 

 

 

 

 

51

 

44

22

7

 

 

 

9

 

 

 

 

 

55

 

 

 

 

32

 

 

 

62

 

9

55

 

 

12

 

58

16

3

 

58

 

 

 

 

 

 

63

 

 

 

 

 

 

 

11

17

 

 

59

 

 

Welded Bracket

 

 

 

 

 

 

 

76

56

 

 

 

 

 

 

 

 

22

48

 

 

 

 

 

18

 

 

 

 

 

Welded Bracket

 

21

 

 

50

 

 

 

 

60

39

 

 

 

 

 

 

 

 

 

42

 

 

 

76

 

 

11

Image 11
Contents Serial Number Decal Model No. WESY74090 Serial NoLimited Warranty Table of ContentsKeep hands and feet away from moving parts Important PrecautionsPrecautions before using the weight system Make sure the cables remain on the pulleysBefore You Begin Using the Weider Weight SystemTo make the assembly process as smooth as possi AssemblyTighten the Nylon Locknuts yet Locate and open the parts bag labeled Frame AssemblySee the inset drawing Bolts with two 5/16 Nylon LocknutsSupport Tighten all Nylon Locknuts used in steps 1 throughIs oriented as shown Locknut 3 do not tighten at this timeLocate and open the parts bag labeled ARM Make sure the welded tab on the Press FrameRight Axle with a hammer ArmCable Trap is oriented as shown Short Cable 58 is between the Pulley 1515b Spacer8 x 1 Bolt 59, a 3/8 Plain Nut 56 and a 3/8 Bracket Onto the Bolt to prevent the Pulley from falling off durIng the following steps. Note Make sure the Pulley From Pulley To PulleySpacer Bolt 12 and a 3/8 Nylon Locknut 21. NoteMake sure the Cable Trap is oriented as shown To the Seat 13 with two 1/4 x 3/4 Screws Shooting and Maintenance on Cable Diagram76, 87 1/2 Long CablePin AdjustmentCise will be reduced Additional slack can be removed by moving the upper Trouble-shooting and MaintenanceMake sure the Cable Trap is oriented as shown Re-install it Woven cable, the type of cable used on the home gym101 120 121 138 103 Weight Resistance ChartCables, pulleys, and weight guides LbsPart No J00885-C R0700A Ordering Replacement PartsWESY74090 R0700A Remove this Part Identification Chart from the ManualPart Identification Chart-WESY74090 Page Page Remove this Part LIST/EXPLODED Drawing from the Manual X 1/4 Spacer Qty Description Key No. Qty16 x 2 1/4 Bolt Upright X 3/4 ScrewExploded Drawing-Model No. WESY74090