Weider WESY74090 Locate and open the parts bag labeled Frame Assembly, See the inset drawing

Page 6

Frame Assembly

1.Before beginning assembly, make sure you have read and understood the information on page 5.

Locate and open the parts bag labeled “FRAME ASSEMBLY.”

Press a 1 1/2” Square Outer Cap (27) onto each end of the Stabilizer (5) and place it on the floor as shown.

Press a 1 1/2” Square Outer Cap (27) onto each end of the Base (4) and place it on the floor as shown.

Place the bracket on the Weight Guide (62) over the

Stabilizer (5). Note: It will be helpful to have a sec- ond person hold the Weight Guide while perform-

ing this step. Line up the holes in the bracket with the holes in the Stabilizer and insert two 5/16” x 2 1/2” Bolts (14).

See the inset drawing.

Slide the bracket on the

 

Base (4) onto the 5/16” x 2 1/2” Bolts (14) and secure

the Bolts with two 5/16” Nylon Locknuts (3).

Do not

tighten the Nylon Locknuts yet.

 

2.Place the bracket on the Upright (42) over the Base

(4).CAUTION: Make sure the Upright is oriented

as shown. Note: It will be helpful to have a sec- ond person hold the Upright while performing this step.

Line up the holes in the bracket on the Upright (42)

with the indicated holes in the Base (4). Slide a 5/16” x 2 1/4” Bolt (1) through the indicated hole and

mount a 5/16” Nylon Locknut (3) onto the Bolt.Do not tighten the Nylon Locknut yet.

Locate the Long Cable (23). It is approximately 233“ long and it has a closed loop on both ends.

See the inset drawing.

Slide a 5/16” x 3 1/4” Bolt

(33)through the closed loop on one end of the Long Cable (23). Slide the Bolt through indicated hole in the bracket on the Upright (42) and the Base (4).

Slide a 1/2” x 3/4” Spacer (45) and a 5/16” Flat Washer (8) onto the 5/16” x 3 1/4” Bolt (33). Hand

tighten a 5/16” Nylon Locknut (3) onto the Bolt.Note:

Leave the Nylon Locknut hand tight when you are asked to tighten the other Locknuts in step 6.

6

1

 

 

5

 

14

62

3

 

 

4

 

3

14

5

27

 

27

3

 

 

27

 

3

 

4

 

27

2

 

 

 

Make sure

 

 

 

 

bracket is on

 

 

 

 

this side

 

 

42

 

23

 

 

 

 

 

 

 

 

4

 

 

 

 

33

 

 

 

 

8

 

 

 

3

45

 

 

 

 

 

 

 

 

23

 

 

 

45

33

 

 

 

 

 

 

 

8

 

 

 

 

 

1

 

4

 

3

 

 

 

 

 

 

 

 

3

 

Image 6
Contents Model No. WESY74090 Serial No Serial Number DecalTable of Contents Limited WarrantyMake sure the cables remain on the pulleys Important PrecautionsPrecautions before using the weight system Keep hands and feet away from moving partsUsing the Weider Weight System Before You BeginAssembly To make the assembly process as smooth as possiBolts with two 5/16 Nylon Locknuts Locate and open the parts bag labeled Frame AssemblySee the inset drawing Tighten the Nylon Locknuts yetTighten all Nylon Locknuts used in steps 1 through SupportMake sure the welded tab on the Press Frame Locknut 3 do not tighten at this timeLocate and open the parts bag labeled ARM Is oriented as shownArm Right Axle with a hammerShort Cable 58 is between the Pulley 15 Cable Trap is oriented as shownSpacer 8 x 1 Bolt 59, a 3/8 Plain Nut 56 and a 3/815b From Pulley To Pulley Onto the Bolt to prevent the Pulley from falling off durIng the following steps. Note Make sure the Pulley BracketBolt 12 and a 3/8 Nylon Locknut 21. Note Make sure the Cable Trap is oriented as shownSpacer To the Seat 13 with two 1/4 x 3/4 Screws Cable Diagram Shooting and Maintenance onLong Cable 76, 87 1/2Adjustment Cise will be reducedPin Woven cable, the type of cable used on the home gym Trouble-shooting and MaintenanceMake sure the Cable Trap is oriented as shown Re-install it Additional slack can be removed by moving the upperLbs Weight Resistance ChartCables, pulleys, and weight guides 101 120 121 138 103Ordering Replacement Parts Part No J00885-C R0700ARemove this Part Identification Chart from the Manual WESY74090 R0700APart Identification Chart-WESY74090 Page Page Remove this Part LIST/EXPLODED Drawing from the Manual X 3/4 Screw Qty Description Key No. Qty16 x 2 1/4 Bolt Upright X 1/4 SpacerExploded Drawing-Model No. WESY74090