Fisher & Paykel 4323 Wash options, Soak, Nappy sanitisers/bleach, Spin Hold, Delay Start

Page 17

Wash options

Soak

15

EXCELLENCE model only

Use the SOAK option to soak clothes at the end of the wash phase or when you wish to re-use the wash water.

When you select SOAK your Smart Drive™ will soak for a period of 2 hours before completing RINSE and SPIN. During SOAK your Smart Drive™ will agitate for a few seconds every minute.

Nappy sanitisers/bleach

Nappy sanitisers and bleach are very corrosive to metal surfaces. These should not be used in your machine.

Important!

EXCELLENCE

Fig.17 Selecting the SOAK option

DO NOT use your Smart Drive™ to soak items in bleach or sanitiser, or tip the contents of the nappy bucket into your machine. The chemicals in these products can damage your washer. Rinse and wring items out thoroughly before placing them in your machine.

Spin Hold

EXCELLENCE & PRIDE model Use the SPIN HOLD option to:

Remove drip dry garments from a mixed load before the wash goes into SPIN.

Minimise the clothes creasing when they are left to sit in the bottom of the bowl at the end of the cycle.

When you have selected SPIN HOLD, your Smart Drive™ will pause at the end of RINSE, beep and the SPIN light will flash to tell you that it is waiting for another instruction.

EXCELLENCE

Press START/PAUSE to begin the spin.

Fig.18 Selecting the SPIN HOLD option

Delay Start

EXCELLENCE model only

DELAY START will delay the start of the wash cycle for 1, 3 or 9 hours.

Press DELAY START once for a delay of 1 hour. Press again for

3 hours, a third time for 9 hours (and again to return to normal).

Once you press DELAY START your Smart Drive™ will begin the delay period, you do not have to press START/PAUSE.

Be careful if using DELAY START for non-colourfast clothes as dyes may run if the clothes are damp.

Your Smart Drive™ will not beep at the end of the cycle if DELAY START is selected.

Note: while EXCELLENCE model is shown, setting of the PRIDE model is identical

Fig.19 Selecting DELAY START

4323_NZ_AU_PAC_GW_MW_Washer_UG11.indd 15

8/10/09 2:45:25 PM

Image 17
Contents Installation instructions Intelligence working for you Contents Unpacking Installation instructionsLocation Drain hoseLevelling Inlet hosesCold supply only To check if your machine is levelAccessories and spare parts Clothes washer safetyWater supply DrainingBefore you do your first wash Getting startedFabric softener Using your Excellence washerDetergent Wash cycles PowerWash options AdvancePride WA55T56MW1 MW512 Fabric softener Using your Pride washerIf you wish to stop your Pride washer LID Lock light Lid lockBasic cycle descriptions Default settingsModel variations Wash options and advancing the cycle Clothes care safeguardsTo select the wash options Wash progress lightsManual water level selection Water levelsAuto water level Excellence model onlyExcellence and Pride model Wash options saving water and timeQuick wash Wash options Delay StartSoak Nappy sanitisers/bleachWashing woollens Washing bulky itemsFavourite cycle Favourite cycleTo set your favourite cycle To use your favourite cycleTo customise a cycle Customising the wash cyclesSorting Before you washLoading Lint givers Lint collectorsChoosing the right detergent DetergentHow much detergent? Adding the detergentFabric softener Cleaning the dispenserHow the fabric softener is dispensed How much fabric softener?Changing pre-set options Option adjustment modeTo enter option adjustment mode Use the buttons on the panel to change the pre-set options Default Wash temperaturesRinse options MED spin light onEnd of cycle beeps Controlled coldAuto water fill level Light on OptionMachine information Out of balance recovery routineSpecifications Cleaning your Smart Drive When you have finishedCleaning the inside of your Smart Drive Cold water washingAutomatic lint system Products that might damage your Smart DriveSmart Drive sounds and beeps Recycling the water from a deep rinse Saving waterRecycling the wash water Return Hose to Drain Manual suds save with syphon backCold water temperature light is flashing HOT water temperature light is flashingHOT and Cold water temperature lights are flashing High water level light is flashingIf your Smart Drive beeps for help Single beep every second and... possible solutionsLID Lock light is flashing Some lights are on but the pattern of lights is unfamiliarOperating problems Wash problems Tangling Dye transferThis warranty does not cover Manufacturer’s WarrantyFisher & Paykel undertakes to Please keep this User Guide in a safe placeCustomer Care Before you call for service or assistance…New Zealand if you need assistance Australia if you need assistanceNZ AU PAC