Fisher & Paykel 4323 Inlet hoses, Levelling, Cold supply only, To check if your machine is level

Page 5

Installation instructions

3

Inlet hoses

1Connect the straight ends of the inlet hoses to the taps. There are washers fitted in both ends.

2Connect the elbow ends of the inlet hoses to the machine inlet valves. Inlet valves are marked on the back of the machine

H=HotC=Cold

3Ensure you have correctly connected hot to hot, and cold to cold.

Tap end

Machine end

Fig.3 Inlet hose ends

Cold supply only:

If you only have a cold water supply, an inlet valve cap (blanking cap) MUST be connected to the hot inlet valve. The cap prevents water leaking out of the hot valve. The cap is available from your Fisher & Paykel Dealer or Authorised Repairer, Part No. 388491. This appliance incorporates backflow protection complying with AS3500.1. No further backflow protection is required for connection to the water supply.

Levelling

It is IMPORTANT to level the machine to ensure even spin performance.

1Separate the four rubber foot inserts from the moulding and fit into the feet on the base of the machine.

2Move the machine to its final position (we suggest a minimum clearance of 20 mm each side).

3Adjust the feet (wind down) so the machine is level and cannot rock.

Corner cabinets

Adjustable feet Rubber insert

Fig.4 Adjusting levelling feet

To check if your machine is level:

Look down on the wash bowl and make sure it sits slightly forward of centre. Close the lid. Visually check that the lid fits evenly on both sides (see Fig.5). If not, adjust one of the front feet slightly until it matches. The diagram on the top and bottom are not correct.

Correct

Incorrect

To check levelling look

Wind left foot down (out) to correct

Wind right foot down (out) to correct

Lid Alignment

Lid

Topdeck Lid

Topdeck Lid

Topdeck

down on the wash bowl

Fig.5 To assess levelling check lid alignment

4Turn on the water and check all hose connections for leaks. Make sure there are no kinks in the hoses.

5Uncoil power cord, remove and discard the plastic pin cover and plug into wall socket.

4323_NZ_AU_PAC_GW_MW_Washer_UG11.indd 3

8/10/09 2:45:22 PM

Image 5
Contents Installation instructions Intelligence working for you Contents Unpacking Installation instructionsLocation Drain hoseLevelling Inlet hosesCold supply only To check if your machine is levelAccessories and spare parts Clothes washer safetyWater supply DrainingBefore you do your first wash Getting startedFabric softener Using your Excellence washerDetergent Wash cycles PowerWash options AdvancePride WA55T56MW1 MW512 Fabric softener Using your Pride washerIf you wish to stop your Pride washer LID Lock light Lid lockBasic cycle descriptions Default settingsModel variations Wash options and advancing the cycle Clothes care safeguardsTo select the wash options Wash progress lightsManual water level selection Water levelsAuto water level Excellence model onlyExcellence and Pride model Wash options saving water and timeQuick wash Wash options Delay StartSoak Nappy sanitisers/bleachWashing woollens Washing bulky itemsFavourite cycle Favourite cycleTo set your favourite cycle To use your favourite cycleTo customise a cycle Customising the wash cyclesSorting Before you washLoading Lint givers Lint collectorsChoosing the right detergent DetergentHow much detergent? Adding the detergentFabric softener Cleaning the dispenserHow the fabric softener is dispensed How much fabric softener?Changing pre-set options Option adjustment modeTo enter option adjustment mode Use the buttons on the panel to change the pre-set options Default Wash temperaturesRinse options MED spin light onEnd of cycle beeps Controlled coldAuto water fill level Light on OptionMachine information Out of balance recovery routineSpecifications Cleaning your Smart Drive When you have finishedCleaning the inside of your Smart Drive Cold water washingAutomatic lint system Products that might damage your Smart DriveSmart Drive sounds and beeps Recycling the water from a deep rinse Saving waterRecycling the wash water Return Hose to Drain Manual suds save with syphon backCold water temperature light is flashing HOT water temperature light is flashingHOT and Cold water temperature lights are flashing High water level light is flashingIf your Smart Drive beeps for help Single beep every second and... possible solutionsLID Lock light is flashing Some lights are on but the pattern of lights is unfamiliarOperating problems Wash problems Tangling Dye transferThis warranty does not cover Manufacturer’s WarrantyFisher & Paykel undertakes to Please keep this User Guide in a safe placeCustomer Care Before you call for service or assistance…New Zealand if you need assistance Australia if you need assistanceNZ AU PAC