Fisher & Paykel 4323 Water supply, Draining, Clothes washer safety, Accessories and spare parts

Page 6
Hot ‘N’ Safe Valves available are:
RMC TVA 50HF
RMC TVA 75HFS
Adjustable between 35°C – 55°C
RMC TVA 50HP
For instantaneous gas hot water supply

4

Installation instructions

Water supply

For best operating conditions your hot water should be approximately 65°C. Your cold water should not exceed 35°C or your hot water exceed 75°C. Temperatures above these may cause the machine to fault or cause damage to the machine. If you have an uncontrolled water heating source (eg a wet back or solar heating system) you should

fit a Safe Valve. This will ensure the hot water temperature remains within safe limits. Inlet water pressure: Max.1 MPa (150 psi) Min. 34 Pa (5 psi)

Inlet water flow rate: Min. 3 litres/min

Minimum height of taps to clear the top of the machine is 1150 mm.

Draining

Regularly check that your standpipe or tub is free from lint or other obstructions, which may affect how your machine works or may cause flooding.

In multi-storey apartments or any upper floor, the machine should be installed on a drained floor. Draining must comply with local by-laws.

Clothes washer safety

This clothes washer is not intended for use by children and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Your Smart Drive™ can be opened while it is filling and agitating. Supervise children at all times to ensure they do not play with the washer.

WARNING!

Electrical Shock Hazard

If you are using an extension cord or a portable electrical outlet device (eg multi-socket outlet box), ensure that it is positioned so that it does not come into contact with water or moisture.

Failure to do so may result in death or electrical shock.

Accessories and spare parts

Available from your Fisher & Paykel Dealer or Authorised Repairer.

 

Inlet Valve Cap

Part No. 388491

 

 

 

 

 

 

Hose Inlet Long (2m)

Part No. 422680

 

 

 

 

 

Hose Inlet Large Bore

Part No. 426123

 

 

 

 

 

Drain Hose Extension

Part No. 425627p

 

 

 

 

 

Power Cord

If the power cord of your clothes washer is damaged it must be replaced

 

 

by a Fisher & Paykel Authorised Repairer, as it is not a standard power cord.

 

 

 

 

 

 

 

 

4323_NZ_AU_PAC_GW_MW_Washer_UG11.indd 4

8/10/09 2:45:22 PM

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation instructions Intelligence working for you Contents Location Installation instructionsUnpacking Drain hoseCold supply only Inlet hosesLevelling To check if your machine is levelWater supply Clothes washer safetyAccessories and spare parts DrainingGetting started Before you do your first washUsing your Excellence washer DetergentFabric softener Wash options PowerWash cycles AdvanceUsing your Pride washer Pride WA55T56MW1 MW512 Fabric softenerIf you wish to stop your Pride washer Lid lock LID Lock lightDefault settings Model variationsBasic cycle descriptions To select the wash options Clothes care safeguardsWash options and advancing the cycle Wash progress lightsAuto water level Water levelsManual water level selection Excellence model onlyWash options saving water and time Quick washExcellence and Pride model Soak Delay StartWash options Nappy sanitisers/bleachWashing bulky items Washing woollensTo set your favourite cycle Favourite cycleFavourite cycle To use your favourite cycleCustomising the wash cycles To customise a cycleLoading Before you washSorting Lint givers Lint collectorsHow much detergent? DetergentChoosing the right detergent Adding the detergentHow the fabric softener is dispensed Cleaning the dispenserFabric softener How much fabric softener?Option adjustment mode To enter option adjustment modeChanging pre-set options Use the buttons on the panel to change the pre-set options Rinse options Wash temperaturesDefault MED spin light onAuto water fill level Controlled coldEnd of cycle beeps Light on OptionOut of balance recovery routine SpecificationsMachine information Cleaning the inside of your Smart Drive When you have finishedCleaning your Smart Drive Cold water washingProducts that might damage your Smart Drive Smart Drive sounds and beepsAutomatic lint system Saving water Recycling the wash waterRecycling the water from a deep rinse Manual suds save with syphon back Return Hose to DrainHOT and Cold water temperature lights are flashing HOT water temperature light is flashingCold water temperature light is flashing High water level light is flashingLID Lock light is flashing Single beep every second and... possible solutionsIf your Smart Drive beeps for help Some lights are on but the pattern of lights is unfamiliarOperating problems Wash problems Dye transfer TanglingFisher & Paykel undertakes to Manufacturer’s WarrantyThis warranty does not cover Please keep this User Guide in a safe placeNew Zealand if you need assistance Before you call for service or assistance…Customer Care Australia if you need assistanceNZ AU PAC
Top Page Image Contents