Maytag MLE/MLG23PDC, MDE/MDG21PRA, MDE/MDG21PNA manual Roller and Bearing Assembly, Back Seal

Page 44

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to unit before servicing.

Four

Screws

6.From back of dryer, remove four screws holding Tumbler Back Assembly.

7.Remove the assembly.

Note: When reinstalling, the seal will be mounted to the tumbler back in a clockwise rotation. Start at the 11:00 position and place under the locking tabs.

The seal will overlap 1 1/4". The coated side (which is the lighter of the two colors) goes against the tumbler. The seal is then looped in a "U" shape so the lighter colored side is against the tumbler back as it is slid in place under the tabs. Bend tabs back over seal with a flat-bladed screwdriver.

Roller and Bearing Assembly

1.Disconnect power supply to unit.

2.Remove Front Shroud/ Assembly

3.Remove Tumbler and Belt.

4.Remove retaining ring from groove in shaft

5.Remove fiber washer and roller.

6.Remove nut securing roller shaft.

Back Seal

1.Disconnect power supply to unit.

2.Remove Tumbler Back Assembly.

Note: For ease in servicing, we recommend removal of the Tumbler Back Assembly from the dryer. This will ensure the felt seal is secured properly.

3.Remove the old felt seal by prying the locking tabs out with a flat-blade screwdriver.

Note: Pay close attention to the location of the seal overlap. This will be important as you install the new seal.

Felt

Tumbler Rides on Light-Colored Side of Felt.

Rear Bulkhead

Dark-Colored Side of Felt is Clamped to the Channel of the Rear Bulkhead by Tabs.

Nut

Washer

Roller Shaft

Roller

Fiber Washer

Retaining Ring

Note: There is a spacer behind the roller. When replacing parts, be certain of the order of the replacement.

44

16022904 Rev. 0

©2004 Maytag Appliances Company

Image 44
Contents Commercial Single Stack Dryers Important Information Table of Contents Important Safety Information Proper Grounding and Polarization of 120 Volts Wall Outlets About Ground WiresGeneral Information Related Publications Grounding Instructions ExplanationService Parts and AccessoriesModel Identification Commercial Dryer NomenclatureAir movement measured in cubic feet per minute TERMINOLOGY/DEFINITIONS Term DefinitionsWater 1 o F GAS Valve Assembly HOW IT WorksFunction of Gas Valve System Radiant Sensor Contact ClosedSafety Features Power InterruptionsGas Conversions Ignition FailuresGeneral Information Exhaust Ducts General SpecificationsWattage Specifications Electrical Troubleshooting Drive Motor CheckCentrifugal Switch Air Shutter AdjustmentMotor Test Cord Drive Motor TestHow to Use ManometersMechanical Troubleshooting Will Not Run Will Not Shut-OffWill Not Dry Noisy and/Or VibrationSingle Dryer Troubleshooting Guide Dryer Stopped with Zero Minutes Remaining Display Cannot Enter OrExit OperatorDisplay Flashes User Mode Dropped Into Machine Credited Are Eventually LostKey Inputs Control Does NotRespond To Dryer Drum Will Not Turn Response To Coin 1 orWill Not Keep Time Of Day During Power Interruptions Will not Respond to handheldNo Decimal Point Is UsedNot Heat Dryer WillSingle Dryer Diagnostic Program Dryer Diagnostic ProgramSingle Dryer Diagnostic Code Door Sense ProblemVAC Stack Dryer Troubleshooting Guide Display Is BlankAbnormal Display Or Function Upper or Lower Dryer Has Zero Minutes Remaining DisplayControl Board DoesNot KeypadsResponse To Coin Or Coin Keep Time DayDuring InterruptionCannot Dryer Runs Without Program Selection Drum Will Not Turn Stack Dryer Diagnostic Program Stack Dryer Diagnostic Code D1 or d17 Door Sense ProblemVoltage Problem Touch Pad Assembly Control PanelMicroprocessor Board TransformerService Door Switch Coin Vault SwitchDoor Assembly Coin SensorFront Panel Reversing Door AssemblyDoor Disassembly Door Switch Top CoverFront Shroud Assembly Removal Outlet Duct, Shroud & Tumbler FrontLint Filter Bearing & PadsFront Seal BeltBaffles Rear Shroud AssemblyInstalling Drive Belt Roller and Bearing Assembly Back SealBlower Assembly ThermostatsCycling Thermostat Low-cycling ThermostatBlower Idler Arm Assembly Exhaust Duct Pipe Assembly BreakdownMotor Switch Drive Motor Assembly Igniter Gas Valve AssemblyCoils Gas Valve Combustion ConeInlet Duct Heater EnclosureStack Dryer Sloped Front Models Service Panel and SwitchAccess Cover Microprocessor Coin DropRemove Screws Swing Out AwayStack Dryer Sloped Front PR Stack DRYER-MN ModelsPush-To-Start Switch TimerSelector Switch Machine-In-Use LightFront Shroud Assembly Stack DRYER-FLAT Front ModelsMotor & Heater Relays Appendix a Programming Procedures PricingFixed Vend Pricing SET UP Codes Steps 3. thru 9. codes are skipped if mode 2.00 is selected Money Counter Option00 7.STARTING of Special Pricing Hour Value of Coin 2 Canadian Dollar Drop White & Colors keypad Example Dryer Diagnostic Mode Dryer Help ModeAll Single Load Models Stacked Models Only