Maytag MLE/MLG23PRF, MDE/MDG21PRA manual Baffles, Rear Shroud Assembly, Installing Drive Belt

Page 43

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to unit before servicing.

4.Grasp the idler pulley in left hand, pull idler upward and to the left.

Note: There is a built-in stop to prevent overstressing of the idler arm spring. Slip belt off the motor pulley.

5. Slip the belt off the back of the tumbler.

Pull to the Side

Work the Belt Off of the Pulley

6. While lifting top cover, pull tumbler out of cabinet.

Installing Drive Belt

1.Disconnect power supply to unit.

2.Place belt onto the outside of the tumbler and position the belt 1 1/2" in front of rear baffle mounting screws with ribbed side against tumbler.

Rear

Bulkhead

Baffle Rear

Mounting Screw

Belt

5.Locate the belt and create a small loop with your right hand, ensuring the belt is free of twist.

6.Position the open end of the loop (ribbed side down) onto the motor pulley with your right hand.

7.To clear the drive belt, grasp the idler pulley in left hand, pull idler up and to the left.

NOTE: There is a built-in stop to prevent overstressing of the idler arm spring.

8.Relax your left hand and allow the idler pulley to rest down onto the belt.

9.Grasp baffles with both hands and rotate tumbler 1 or 2 turns clockwise to allow the belt to align itself.

As Viewed From The Front

Tumbler Belt

Cylinder

Idler

Pulley

Motor

Pulley

Baffles

1.Disconnect power supply to unit.

2.Remove Front Panel and Door.

3.Lift Top Cover.

4.Rotate the tumbler until the screws of the baffle to be removed appear at the top of the tumbler.

5.Remove two screws holding the baffle to the tumbler.

3.Position tumbler into the rear felt seal, resting the tumbler onto the rear rollers. Lower the front of the tumbler onto the blower housing.

4.Insert left hand along side of tumbler at 8 o'clock. Insert right arm under tumbler (as close to blower as possible).

Rear Shroud Assembly

1.Disconnect power supply to unit.

2.Remove Front Shroud Assembly.

3.Remove Tumbler and Belt

4.Remove Gas Valve Assembly or Heater Assembly.

Note: Be careful on gas models, the igniter is fragile.

5. Remove heat enclosure.

©2004 Maytag Appliances Company

16022904 Rev. 0

43

Image 43
Contents Commercial Single Stack Dryers Important Information Table of Contents Important Safety Information General Information Related Publications About Ground WiresProper Grounding and Polarization of 120 Volts Wall Outlets Explanation Grounding InstructionsCommercial Dryer Nomenclature ServiceParts and Accessories Model IdentificationWater 1 o F TERMINOLOGY/DEFINITIONS Term DefinitionsAir movement measured in cubic feet per minute HOW IT Works GAS Valve AssemblyRadiant Sensor Contact Closed Function of Gas Valve SystemIgnition Failures Safety FeaturesPower Interruptions Gas ConversionsGeneral Information Wattage Specifications General SpecificationsExhaust Ducts Drive Motor Check Electrical TroubleshootingDrive Motor Test Centrifugal SwitchAir Shutter Adjustment Motor Test CordManometers How to UseNoisy and/Or Vibration Mechanical Troubleshooting Will Not RunWill Not Shut-Off Will Not DrySingle Dryer Troubleshooting Guide Operator Dryer Stopped with Zero Minutes Remaining DisplayCannot Enter Or ExitDropped Into Machine Credited Are Eventually Lost Display Flashes User ModeRespond To Control Does NotKey Inputs Dryer Drum Will Not Turn To Coin 1 or ResponsePoint Is Used Will Not Keep Time Of Day During Power InterruptionsWill not Respond to handheld No DecimalDryer Will Not HeatDryer Diagnostic Program Single Dryer Diagnostic ProgramDoor Sense Problem Single Dryer Diagnostic CodeVAC Lower Dryer Has Zero Minutes Remaining Display Stack Dryer Troubleshooting GuideDisplay Is Blank Abnormal Display Or Function Upper orKeypads ControlBoard Does NotInterruption Response To Coin Or CoinKeep Time Day DuringCannot Dryer Runs Without Program Selection Drum Will Not Turn Stack Dryer Diagnostic Program D1 or d17 Door Sense Problem Stack Dryer Diagnostic CodeVoltage Problem Transformer Touch Pad AssemblyControl Panel Microprocessor BoardCoin Sensor Service Door SwitchCoin Vault Switch Door AssemblyDoor Disassembly Reversing Door AssemblyFront Panel Top Cover Door SwitchOutlet Duct, Shroud & Tumbler Front Front Shroud Assembly RemovalBelt Lint FilterBearing & Pads Front SealInstalling Drive Belt Rear Shroud AssemblyBaffles Back Seal Roller and Bearing AssemblyLow-cycling Thermostat Blower AssemblyThermostats Cycling ThermostatBlower Motor Switch Drive Motor Assembly Exhaust Duct Pipe Assembly BreakdownIdler Arm Assembly Coils Gas Valve AssemblyIgniter Heater Enclosure Gas ValveCombustion Cone Inlet DuctAccess Cover Service Panel and SwitchStack Dryer Sloped Front Models Coin Drop MicroprocessorSwing Out Away Remove ScrewsStack DRYER-MN Models Stack Dryer Sloped Front PRMachine-In-Use Light Push-To-Start SwitchTimer Selector SwitchStack DRYER-FLAT Front Models Front Shroud AssemblyMotor & Heater Relays Appendix a Pricing Programming ProceduresFixed Vend Pricing SET UP Codes Money Counter Option Steps 3. thru 9. codes are skipped if mode 2.00 is selected00 7.STARTING of Special Pricing Hour Value of Coin 2 Canadian Dollar Drop White & Colors keypad Example Stacked Models Only Dryer Diagnostic ModeDryer Help Mode All Single Load Models