Maytag MLE/MLG23PDA manual Thermostats, Cycling Thermostat, Low-cycling Thermostat, Thermal Fuse

Page 45

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to unit before servicing.

Thermostats

1.Disconnect power supply to unit.

2.Remove Front Panel.

Note: Thermostats are located on Blower Cover. Hi- Limit Thermostat and is located on heating source for gas and electric models.

Cycling

Thermostat

Thermal

Fuse

Low Cycling

Thermostat

Cycling Thermostat

1.Disconnect power supply to unit.

2.Remove Front Panel.

3.Disconnect wires to Cycling Thermostat.

4.Remove two screws securing thermostat to blower cover.

Low-cycling Thermostat

1.Disconnect power supply to unit.

2.Remove Front Panel.

3.Disconnect wires to Low-Cycling Thermostat.

4.Remove Two screws securing thermostat to blower cover.

Thermal Fuse

1.Disconnect power supply to unit.

2.Remove Front Panel.

3.Disconnect wires to Thermal Fuse.

4.Remove Two screws securing fuse to blower cover.

Hi-Limit Thermostat

1.Disconnect power supply to unit.

2.Remove Front Panel.

Note: Hi-Limit Thermostat is located on the right hand side of the Heating Cone for Gas Models and on the left hand side for Electric Models.

3.Disconnect wires to Hi-Limit Thermostat .

4.Loosen the rear mounting screw and remove the front screw.

Note: The mounting tabs of the thermostat are open- slotted.

Blower Assembly

1.Disconnect power supply to unit.

2.Remove Front Panel.

3.Remove Front Shroud Assembly.

Blower Seal

1.Disconnect power supply to unit.

2.`Remove Front Shroud Assembly.

Note: The rubber seal is secured to the outlet duct opening. The seal is fitted around the outer circumference lip of the outlet duct with the flange of the seal facing the blower cover.

Air Outlet

Seal

Air Outlet

Duct

Note: “MDE” dryers (Electric Dryer Models) also have a

Thermal Fuse mounted on the Heater Enclosure. Blower Cover

1. Disconnect power supply to unit.

2. Remove Front Shroud Assembly.

3. Remove screws holding cover to blower housing.

Note: One screw secures blower Cover to base frame.

©2004 Maytag Appliances Company

16022904 Rev. 0

45

Image 45

Contents Commercial Single Stack Dryers Important Information Table of Contents Important Safety Information About Ground Wires General Information Related PublicationsProper Grounding and Polarization of 120 Volts Wall Outlets Explanation Grounding InstructionsParts and Accessories ServiceModel Identification Commercial Dryer NomenclatureTERMINOLOGY/DEFINITIONS Term Definitions Water 1 o FAir movement measured in cubic feet per minute HOW IT Works GAS Valve AssemblyRadiant Sensor Contact Closed Function of Gas Valve SystemPower Interruptions Safety FeaturesGas Conversions Ignition FailuresGeneral Information General Specifications Wattage SpecificationsExhaust Ducts Drive Motor Check Electrical TroubleshootingAir Shutter Adjustment Centrifugal SwitchMotor Test Cord Drive Motor TestManometers How to UseWill Not Shut-Off Mechanical Troubleshooting Will Not RunWill Not Dry Noisy and/Or VibrationSingle Dryer Troubleshooting Guide Cannot Enter Or Dryer Stopped with Zero Minutes Remaining DisplayExit OperatorDropped Into Machine Credited Are Eventually Lost Display Flashes User ModeControl Does Not Respond ToKey Inputs Dryer Drum Will Not Turn To Coin 1 or ResponseWill not Respond to handheld Will Not Keep Time Of Day During Power InterruptionsNo Decimal Point Is UsedDryer Will Not HeatDryer Diagnostic Program Single Dryer Diagnostic ProgramDoor Sense Problem Single Dryer Diagnostic CodeVAC Display Is Blank Stack Dryer Troubleshooting GuideAbnormal Display Or Function Upper or Lower Dryer Has Zero Minutes Remaining DisplayBoard Does ControlNot KeypadsKeep Time Day Response To Coin Or CoinDuring InterruptionCannot Dryer Runs Without Program Selection Drum Will Not Turn Stack Dryer Diagnostic Program D1 or d17 Door Sense Problem Stack Dryer Diagnostic CodeVoltage Problem Control Panel Touch Pad AssemblyMicroprocessor Board TransformerCoin Vault Switch Service Door SwitchDoor Assembly Coin SensorReversing Door Assembly Door DisassemblyFront Panel Top Cover Door SwitchOutlet Duct, Shroud & Tumbler Front Front Shroud Assembly RemovalBearing & Pads Lint FilterFront Seal BeltRear Shroud Assembly Installing Drive BeltBaffles Back Seal Roller and Bearing AssemblyThermostats Blower AssemblyCycling Thermostat Low-cycling ThermostatBlower Exhaust Duct Pipe Assembly Breakdown Motor Switch Drive Motor AssemblyIdler Arm Assembly Gas Valve Assembly CoilsIgniter Combustion Cone Gas ValveInlet Duct Heater EnclosureService Panel and Switch Access CoverStack Dryer Sloped Front Models Coin Drop MicroprocessorSwing Out Away Remove ScrewsStack DRYER-MN Models Stack Dryer Sloped Front PRTimer Push-To-Start SwitchSelector Switch Machine-In-Use LightStack DRYER-FLAT Front Models Front Shroud AssemblyMotor & Heater Relays Appendix a Pricing Programming ProceduresFixed Vend Pricing SET UP Codes Money Counter Option Steps 3. thru 9. codes are skipped if mode 2.00 is selected00 7.STARTING of Special Pricing Hour Value of Coin 2 Canadian Dollar Drop White & Colors keypad Example Dryer Help Mode Dryer Diagnostic ModeAll Single Load Models Stacked Models Only